kea/doc/guide/dhcp6-srv.xml

<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE book PUBLIC "-//OASIS//DTD DocBook XML V4.2//EN"
"http://www.oasis-open.org/docbook/xml/4.2/docbookx.dtd" [
<!ENTITY mdash  "&#x2014;" >
]>

 <chapter id="dhcp6">
    <title>The DHCPv6 Server</title>

    <section id="dhcp6-start-stop">
      <title>Starting and Stopping the DHCPv6 Server</title>

      <para>
        It is recommended that the Kea DHCPv6 server be started and stopped
        using <command>keactrl</command> (described in <xref linkend="keactrl"/>).
        However, it is also possible to run the server directly: it accepts
        the following command-line switches:
      </para>

      <itemizedlist>
          <listitem>
            <simpara>
            <command>-c <replaceable>file</replaceable></command> -
            specifies the configuration file. This is the only mandatory
            switch.</simpara>
          </listitem>
          <listitem>
            <simpara>
            <command>-d</command> - specifies whether the server
            logging should be switched to verbose mode. In verbose mode,
            the logging severity and debuglevel specified in the configuration
            file are ignored and "debug" severity and the maximum debuglevel
            (99) are assumed. The flag is convenient, for temporarily
            switching the server into maximum verbosity, e.g. when
            debugging.</simpara>
          </listitem>
          <listitem>
            <simpara>
            <command>-p <replaceable>port</replaceable></command> -
            specifies UDP port on which the server will listen. This is only
            useful during testing, as a DHCPv6 server listening on
            ports other than the standard ones will not be able to
            handle regular DHCPv6 queries.</simpara>
          </listitem>
          <listitem>
            <simpara>
            <command>-t <replaceable>file</replaceable></command> -
            specifies the configuration file to be tested. Kea-dhcp6
            will attempt to load it, and will conduct sanity
            checks. Note that certain checks are possible only while
            running the actual server. The actual status is reported
            with exit code (0 = configuration looks ok, 1 = error
            encountered). Kea will print out log messages to standard
            output and error to standard error when testing
            configuration.</simpara>
          </listitem>
          <listitem>
            <simpara>
              <command>-v</command> - prints out the Kea version and exits.
            </simpara>
          </listitem>
          <listitem>
            <simpara>
              <command>-V</command> - prints out the Kea extended version with
              additional parameters and exits. The listing includes the versions
              of the libraries dynamically linked to Kea.
            </simpara>
          </listitem>
          <listitem>
            <simpara>
              <command>-W</command> - prints out the Kea configuration report
              and exits. The report is a copy of the
              <filename>config.report</filename> file produced by
              <userinput>./configure</userinput>: it is embedded in the
              executable binary.
            </simpara>
          </listitem>
      </itemizedlist>

      <para>
        The <filename>config.report</filename> may also be accessed more
        directly.  The following command may be used to extract this
        information.  The binary <userinput>path</userinput> may be found
        in the install directory or in the <filename>.libs</filename>
        subdirectory in the source tree. For example
        <filename>kea/src/bin/dhcp6/.libs/kea-dhcp6</filename>.

<screen>
strings <userinput>path</userinput>/kea-dhcp6 | sed -n 's/;;;; //p'
</screen>
      </para>

      <para>
        On start-up, the server will detect available network interfaces
        and will attempt to open UDP sockets on all interfaces
        mentioned in the configuration file.
        Since the DHCPv6 server opens privileged ports, it requires root
        access. Make sure you run this daemon as root.
      </para>

      <para>
        During startup the server will attempt to create a PID file of the
        form: localstatedir]/[conf name].kea-dhcp6.pid where:
        <itemizedlist>
            <listitem>
            <simpara><command>localstatedir</command>: The value as passed into the
            build configure script. It defaults to "/usr/local/var".  Note
            that this value may be overridden at run time by setting the environment
            variable KEA_PIDFILE_DIR.  This is intended primarily for testing purposes.
            </simpara>
            </listitem>
            <listitem>
            <simpara><command>conf name</command>: The configuration file name
            used to start the server, minus all preceding path and file extension.
            For example, given a pathname of "/usr/local/etc/kea/myconf.txt", the
            portion used would be "myconf".
            </simpara>
            </listitem>
        </itemizedlist>
        If the file already exists and contains the PID of a live process,
        the server will issue a DHCP6_ALREADY_RUNNING log message and exit. It
        is possible, though unlikely, that the file is a remnant of a system crash
        and the process to which the PID belongs is unrelated to Kea.  In such a
        case it would be necessary to manually delete the PID file.
      </para>

      <para>
        The server can be stopped using the <command>kill</command> command.
        When running in a console, the server can be shut down by
        pressing ctrl-c. It detects the key combination and shuts
        down gracefully.
      </para>
    </section>

    <section id="dhcp6-configuration">
      <title>DHCPv6 Server Configuration</title>
<section>
  <title>Introduction</title>
      <para>
        This section explains how to configure the DHCPv6 server using the
        Kea configuration backend. (Kea configuration using any other
        backends is outside of scope of this document.) Before DHCPv6
        is started, its configuration file has to be created. The
        basic configuration is as follows:
<screen>
{
# DHCPv6 configuration starts on the next line
"Dhcp6": {

# First we set up global values
    "valid-lifetime": 4000,
    "renew-timer": 1000,
    "rebind-timer": 2000,
    "preferred-lifetime": 3000,

# Next we setup the interfaces to be used by the server.
    "interfaces-config": {
        "interfaces": [ "eth0" ]
    },

# And we specify the type of lease database
    "lease-database": {
        "type": "memfile",
        "persist": true,
        "name": "/var/kea/dhcp6.leases"
    },

# Finally, we list the subnets from which we will be leasing addresses.
    "subnet6": [
        {
            "subnet": "2001:db8:1::/64",
            "pools": [
                 {
                     "pool": "2001:db8:1::1-2001:db8:1::ffff"
                 }
             ]
        }
    ]
# DHCPv6 configuration ends with the next line
}

} </screen>
</para>

<para>The following paragraphs provide a brief overview of the parameters in
the above example together with
their format. Subsequent sections of this chapter go into much greater detail
for these and other parameters.</para>

<para>The lines starting with a hash (#) are comments and are ignored by
the server; they do not impact its
operation in any way.</para>

<para>The configuration starts in the first line with the initial
opening curly bracket (or brace). Each configuration consists of
one or more objects. In this specific example, we have only one
object, called Dhcp6. This is a simplified configuration, as usually
there will be additional objects, like <command>Logging</command> or
<command>DhcpDdns</command>, but we omit them now for clarity. The Dhcp6
configuration starts with the <command>"Dhcp6": {</command> line
and ends with the corresponding closing brace (in the above example,
the brace after the last comment).  Everything defined between those
lines is considered to be the Dhcp6 configuration.</para>

<para>In the general case, the order in which those parameters appear does not
matter. There are two caveats here though. The first one is to remember that
the configuration file must be well formed JSON. That means that parameters
for any given scope must be separated by a comma and there must not be a comma
after the last parameter. When reordering a configuration file, keep in mind that
moving a parameter to or from the last position in a given scope may also require
moving the comma. The second caveat is that it is uncommon &mdash; although
legal JSON &mdash; to
repeat the same parameter multiple times. If that happens, the last occurrence of a
given parameter in a given scope is used while all previous instances are
ignored. This is unlikely to cause any confusion as there are no real life
reasons to keep multiple copies of the same parameter in your configuration
file.</para>

<para>Moving onto the DHCPv6 configuration elements, the very first few elements
define some global parameters. <command>valid-lifetime</command>
defines for how long the addresses (leases) given out by the server are valid. If
nothing changes, a client that got an address is allowed to use it for 4000
seconds. (Note that integer numbers are specified as is, without any quotes
around them.) The address will become deprecated in 3000 seconds (clients are
allowed to keep old connections, but can't use this address for creating new
connections). <command>renew-timer</command> and
<command> rebind-timer</command> are values that define T1 and T2 timers that
govern when the client will begin the renewal and rebind procedures.</para>

<para>The <command>interfaces-config</command> map specifies the server
configuration concerning the network interfaces, on which the server should
listen to the DHCP messages. The <command>interfaces</command> parameter
specifies a list of network interfaces on which the server should listen.
Lists are opened and closed with square brackets, with elements separated
by commas. Had we wanted to listen on two interfaces, the
<command>interfaces-config</command> would look like this:
<screen>
"interfaces-config": {
    "interfaces": [ "eth0", "eth1" ]
},
</screen>
</para>

<para>The next couple of lines define the lease database, the place where the server
stores its lease information. This particular example tells the server to use
<command>memfile</command>, which is the simplest (and fastest) database
backend. It uses an in-memory database and stores leases on disk in a CSV
file. This is a very simple configuration. Usually the lease database configuration
is more extensive and contains additional parameters.  Note that
<command>lease-database</command>
is an object and opens up a new scope, using an opening brace.
Its parameters (just one in this example - <command>type</command>)
follow. Had there been more than one, they would be separated by commas. This
scope is closed with a closing brace. As more parameters for the Dhcp6 definition
follow, a trailing comma is present.</para>

<para>Finally, we need to define a list of IPv6 subnets. This is the
most important DHCPv6 configuration structure as the server uses that
information to process clients' requests. It defines all subnets from
which the server is expected to receive DHCP requests. The subnets are
specified with the <command>subnet6</command> parameter.  It is a list,
so it starts and ends with square brackets.  Each subnet definition in
the list has several attributes associated with it, so it is a structure
and is opened and closed with braces. At minimum, a subnet definition
has to have at least two parameters: <command>subnet</command> (that
defines the whole subnet) and <command>pools</command> (which is a list of
dynamically allocated pools that are governed by the DHCP server).</para>

<para>The example contains a single subnet. Had more than one been defined,
additional elements
in the <command>subnet6</command> parameter would be specified and
separated by commas. For example, to define two subnets, the following
syntax would be used:
<screen>
"subnet6": [
    {
        "pools": [ { "pool": "2001:db8:1::/112" } ],
        "subnet": "2001:db8:1::/64"
    },
    {
        "pools": [ { "pool": "2001:db8:2::1-2001:db8:2::ffff" } ],
        "subnet": "2001:db8:2::/64"
    }
]
</screen>
Note that indentation is optional and is used for aesthetic purposes only.
In some cases in may be preferable to use more compact notation.
</para>

<para>After all parameters are specified, we have two contexts open:
global and Dhcp6, hence we need two closing curly brackets to close them.
In a real life configuration file there most likely would be additional
components defined such as Logging or DhcpDdns, so the closing brace would
be followed by a comma and another object definition.</para>
</section>

<section>
  <title>Lease Storage</title>
  <para>All leases issued by the server are stored in the lease database.
  Currently there are four database backends available:  memfile (which is the
  default backend), MySQL, PostgreSQL and Cassandra.</para>
<section>
  <title>Memfile - Basic Storage for Leases</title>

  <para>The server is able to store lease data in different repositories. Larger
  deployments may elect to store leases in a database. <xref
  linkend="database-configuration6"/> describes this option. In typical
  smaller deployments though, the server will store lease information in a CSV file rather
  than a database. As well as requiring less administration, an
  advantage of using a file for storage is that it
  eliminates a dependency on third-party database software.</para>

  <para>The configuration of the file backend (Memfile) is controlled through
  the Dhcp6/lease-database parameters. The <command>type</command> parameter
  is mandatory and it specifies which storage for leases the server should use.
  The value of <userinput>"memfile"</userinput> indicates that the file should
  be used as the storage. The following list gives additional, optional,
  parameters that can be used to configure the Memfile backend.

  <itemizedlist>
    <listitem>
      <simpara><command>persist</command>: controls whether the new leases and
      updates to existing leases are written to the file. It is strongly
      recommended that the value of this parameter is set to
      <userinput>true</userinput> at all times, during the server's normal
      operation. Not writing leases to disk will mean that if a server is restarted
      (e.g. after a power failure), it will not know what addresses have been
      assigned.  As a result, it may hand out addresses to new clients that are
      already in use. The value of <userinput>false</userinput> is mostly useful
      for performance testing purposes. The default value of the
      <command>persist</command> parameter is <userinput>true</userinput>,
      which enables writing lease updates
      to the lease file.
      </simpara>
    </listitem>

    <listitem>
      <simpara><command>name</command>: specifies an absolute location of the lease
      file in which new leases and lease updates will be recorded. The default value
      for this parameter is <userinput>"[kea-install-dir]/var/kea/kea-leases6.csv"
      </userinput>.</simpara>
    </listitem>

    <listitem>
      <simpara><command>lfc-interval</command>: specifies the interval in seconds, at
      which the server will perform a lease file cleanup (LFC).  This
      removes redundant (historical) information from the lease file
      and effectively reduces the lease file size. The cleanup process is described
      in more detailed fashion further in this section. The default value of the
      <command>lfc-interval</command> is <userinput>0</userinput>, which disables
      the LFC.</simpara>
    </listitem>

  </itemizedlist>
  </para>

  <para>An example configuration of the Memfile backend is presented below:

<screen>
"Dhcp6": {
    "lease-database": {
        <userinput>"type": "memfile"</userinput>,
        <userinput>"persist": true</userinput>,
        <userinput>"name": "/tmp/kea-leases6.csv"</userinput>,
        <userinput>"lfc-interval": 1800</userinput>
    }
}
</screen>

    This configuration selects the <filename>/tmp/kea-leases6.csv</filename> as
    the storage for lease information and enables persistence (writing lease updates
    to this file). It also configures the backend perform the periodic cleanup
    of the lease files, executed every 30 minutes.
  </para>

  <para>It is important to know how the lease file contents are organized
  to understand why the periodic lease file cleanup is needed. Every time
  the server updates a lease or creates a new lease for the client, the new
  lease information must be recorded in the lease file. For performance reasons,
  the server does not update the existing client's lease in the file, as it would
  potentially require rewriting the entire file. Instead, it simply appends the new lease
  information to the end of the file: the previous lease entries for the
  client are not removed. When the server loads leases from the lease file, e.g.
  at the server startup, it assumes that the latest lease entry for the client
  is the valid one. The previous entries are discarded. This means that the
  server can re-construct the accurate information about the leases even though
  there may be many lease entries for each client. However, storing many entries
  for each client results in bloated lease file and impairs the performance of
  the server's startup and reconfiguration as it needs to process a larger number
  of lease entries.
  </para>

  <para>Lease file cleanup (LFC) removes all previous entries for each client and
  leaves only the latest ones. The interval at which the cleanup is performed
  is configurable, and it should be selected according to the frequency of lease
  renewals initiated by the clients. The more frequent the renewals, the smaller
  the value of <command>lfc-interval</command> should be. Note however, that the
  LFC takes time and thus it is possible (although unlikely) that new cleanup
  is started while the previous cleanup instance is still running, if the
  <command>lfc-interval</command> is too short. The server would recover from
  this by skipping the new cleanup when it detects that the previous cleanup
  is still in progress. But it implies that the actual cleanups will be
  triggered more rarely than configured. Moreover, triggering a new cleanup
  adds an overhead to the server which will not be able to respond to new
  requests for a short period of time when the new cleanup process is spawned.
  Therefore, it is recommended that the <command>lfc-interval</command> value
  is selected in a way that would allow for the LFC to complete the cleanup before a
  new cleanup is triggered.
  </para>

  <para>Lease file cleanup is performed by a separate process (in background) to avoid
  a performance impact on the server process. In order to avoid the conflicts
  between two processes both using the same lease files, the LFC process
  operates on the copy of the original lease file, rather than on the lease
  file used by the server to record lease updates. There are also other files
  being created as a side effect of the lease file cleanup. The detailed
  description of the LFC is located on the Kea wiki:
  <ulink url="http://kea.isc.org/wiki/LFCDesign"/>.
  </para>

</section>

<section id="database-configuration6">
  <title>Lease Database Configuration</title>

  <note>
    <para>Lease database access information must be configured for the DHCPv6 server,
    even if it has already been configured for the DHCPv4 server.  The servers
    store their information independently, so each server can use a separate
    database or both servers can use the same database.</para>
  </note>

  <para>Lease database configuration is controlled through the
  Dhcp6/lease-database parameters. The type of the database must be set to
  "memfile", "mysql", "postgresql" or "cql", e.g.
<screen>
"Dhcp6": { "lease-database": { <userinput>"type": "mysql"</userinput>, ... }, ... }
</screen>
  Next, the name of the database is to hold the leases must be set: this is the
  name used when the database was created
  (see <xref linkend="mysql-database-create"/>,
  <xref linkend="pgsql-database-create"/>
  or <xref linkend="cql-database-create"/>).
<screen>
"Dhcp6": { "lease-database": { <userinput>"name": "<replaceable>database-name</replaceable>" </userinput>, ... }, ... }
</screen>
  If the database is located on a different system to the DHCPv6 server, the
  database host name must also be specified. (It should be noted that this
  configuration may have a severe impact on server performance.):
<screen>
"Dhcp6": { "lease-database": { <userinput>"host": <replaceable>remote-host-name</replaceable></userinput>, ... }, ... }
</screen>
  The usual state of affairs will be to have the database on the same machine as
  the DHCPv6 server.  In this case, set the value to the empty string:
<screen>
"Dhcp6": { "lease-database": { <userinput>"host" : ""</userinput>, ... }, ... }
</screen>
  Should the database use a port different than default, it may be
  specified as well:
<screen>
"Dhcp4": { "lease-database": { <userinput>"port" : 12345</userinput>, ... }, ... }
</screen>
  Should the database be located on a different system, you may need to specify a longer interval
  for the connection timeout:
<screen>
"Dhcp6": { "lease-database": { <userinput>"connect-timeout" : <replaceable>timeout-in-seconds</replaceable></userinput>, ... }, ... }
</screen>
The default value of five seconds should be more than adequate for local connections.
If a timeout is given though, it should be an integer greater than zero.
  </para>

  <para>
    Note that host parameter is used by MySQL and PostgreSQL
    backends. Cassandra has a concept of contact points that could be
    used to contact the cluster, instead of a single IP or
    hostname. It takes a list of comma separated IP addresses. This may be specified as:
<screen>
"Dhcp4": { "lease-database": { <userinput>"contact-points" : "192.0.2.1,192.0.2.2"</userinput>, ... }, ... }
</screen>
  </para>

  <para>Finally, the credentials of the account under which the server will
  access the database should be set:
<screen>
"Dhcp6": { "lease-database": { <userinput>"user": "<replaceable>user-name</replaceable>"</userinput>,
                               <userinput>"password": "<replaceable>password</replaceable>"</userinput>,
                              ... },
           ... }
</screen>
  If there is no password to the account, set the password to the empty string
  "". (This is also the default.)</para>
</section>
</section>

<section id="hosts6-storage">
  <title>Hosts Storage</title>
    <para>Kea is also able to store information about host reservations in the
    database. The hosts database configuration uses the same syntax as the lease
    database. In fact, a Kea server opens independent connections for each
    purpose, be it lease or hosts information. This arrangement gives the most
    flexibility. Kea can be used to keep leases and host reservations
    separately, but can also point to the same database. Currently the
    supported hosts database types are MySQL and PostgreSQL. The Cassandra
    backend does not support host reservations yet.</para>

    <para>Please note that usage of hosts storage is optional. A user can define
    all host reservations in the configuration file. That is the recommended way
    if the number of reservations is small. However, when the number of
    reservations grows it's more convenient to use host storage. Please note
    that both storage methods (configuration file and one of the supported databases)
    can be used together. If hosts are defined in both places, the definitions
    from the configuration file are checked first and external storage is checked
    later, if necessary.</para>

<section id="hosts-database-configuration6">
  <title>DHCPv6 Hosts Database Configuration</title>

  <para>Hosts database configuration is controlled through the Dhcp6/hosts-database
  parameters. If enabled, the type of the database must be set to "mysql" or
  "postgresql". Other hosts backends may be added in later version of Kea.
<screen>
"Dhcp6": { "hosts-database": { <userinput>"type": "mysql"</userinput>, ... }, ... }
</screen>
  Next, the name of the database to hold the reservations must be set: this is the
  name used when the database was created  (see <xref linkend="supported-databases"/>
  for instructions how to setup desired database type).
<screen>
"Dhcp6": { "hosts-database": { <userinput>"name": "<replaceable>database-name</replaceable>" </userinput>, ... }, ... }
</screen>
  If the database is located on a different system than the DHCPv6 server, the
  database host name must also be specified. (Again it should be noted that this
  configuration may have a severe impact on server performance):
<screen>
"Dhcp6": { "hosts-database": { <userinput>"host": <replaceable>remote-host-name</replaceable></userinput>, ... }, ... }
</screen>
  The usual state of affairs will be to have the database on the same machine as
  the DHCPv6 server.  In this case, set the value to the empty string:
<screen>
"Dhcp6": { "hosts-database": { <userinput>"host" : ""</userinput>, ... }, ... }
</screen>
<screen>
"Dhcp4": { "hosts-database": { <userinput>"port" : 12345</userinput>, ... }, ... }
</screen>
  </para>
  <para>Finally, the credentials of the account under which the server will
  access the database should be set:
<screen>
"Dhcp6": { "hosts-database": { <userinput>"user": "<replaceable>user-name</replaceable>"</userinput>,
                               <userinput>"password": "<replaceable>password</replaceable>"</userinput>,
                              ... },
           ... }
</screen>
  If there is no password to the account, set the password to the empty string
  "". (This is also the default.)</para>
</section>

<section id="read-only-database-configuration6">
<title>Using Read-Only Databases for Host Reservations</title>
<para>
In some deployments the database user whose name is specified in the database backend
configuration may not have write privileges to the database. This is often
required by the policy within a given network to secure the data from being
unintentionally modified. In many cases administrators have inventory databases
deployed, which contain substantially more information about the hosts than
static reservations assigned to them. The inventory database can be used to create
a view of a Kea hosts database and such view is often read only.
</para>
<para>
Kea host database backends operate with an implicit configuration to both
read from and write to the database. If the database user does not have
write access to the host database, the backend will fail to start and the
server will refuse to start (or reconfigure). However, if access to a read
only host database is required for retrieving reservations for clients
and/or assign specific addresses and options, it is possible to explicitly
configure Kea to start in "read-only" mode. This is controlled by the
<command>readonly</command> boolean parameter as follows:
<screen>
"Dhcp6": { "hosts-database": { <userinput>"readonly": true</userinput>, ... }, ... }
</screen>
Setting this parameter to <userinput>false</userinput> would configure the
database backend to operate in "read-write" mode, which is also a default
configuration if the parameter is not specified.
</para>
<note><para>The <command>readonly</command> parameter is currently only supported
for MySQL and PostgreSQL databases.</para></note>
</section>

</section>


<section id="dhcp6-interface-selection">
  <title>Interface Selection</title>
  <para>The DHCPv6 server has to be configured to listen on specific network
  interfaces.  The simplest network interface configuration instructs the server to
  listen on all available interfaces:
  <screen>
"Dhcp6": {
    "interfaces-config": {
        "interfaces": [ <userinput>"*"</userinput> ]
    }
    ...
}
</screen>
  The asterisk plays the role of a wildcard and means "listen on all interfaces".
  However, it is usually a good idea to explicitly specify interface names:
  <screen>
"Dhcp6": {
    "interfaces-config": {
        "interfaces": [ <userinput>"eth1", "eth3"</userinput> ]
    },
    ...
}
  </screen>
</para>
  <para>It is possible to use wildcard interface name (asterisk) concurrently
  with the actual interface names:
  <screen>
"Dhcp6": {
    "interfaces-config": {
        "interfaces": [ <userinput>"eth1", "eth3", "*"</userinput> ]
    },
    ...
}
  </screen>
It is anticipated that this will form of usage only be used where it is desired to
temporarily override a list of interface names and listen on all interfaces.
  </para>

  <para>As for the DHCPv4 server binding to specific addresses and
  disabling re-detection of interfaces are supported. But
  <command>dhcp-socket-type</command> is not because DHCPv6 uses
  UDP/IPv6 sockets only. The following example shows how to disable the
  interface detection:
  </para>

  <screen>
"Dhcp6": {
    "interfaces-config": {
        "interfaces": [ <userinput>"eth1", "eth3"</userinput> ],
        "re-detect": <userinput>false</userinput>
    },
    ...
}
  </screen>

</section>

    <section id="ipv6-subnet-id">
      <title>IPv6 Subnet Identifier</title>
      <para>
        The subnet identifier is a unique number associated with a particular subnet.
        In principle, it is used to associate clients' leases with their respective subnets.
        When a subnet identifier is not specified for a subnet being configured, it will
        be automatically assigned by the configuration mechanism. The identifiers
        are assigned from 1 and are monotonically increased for each subsequent
        subnet: 1, 2, 3 ....
      </para>
      <para>
        If there are multiple subnets configured with auto-generated identifiers and
        one of them is removed, the subnet identifiers may be renumbered. For example:
        if there are four subnets and the third is removed the last subnet will be assigned
        the identifier that the third subnet had before removal. As a result, the leases
        stored in the lease database for subnet 3 are now associated with
        subnet 4, something that may have unexpected consequences. It is planned
        to implement a mechanism to preserve auto-generated subnet ids in a
        future version of Kea.  However, the only remedy for this issue
        at present is to
        manually specify a unique identifier for each subnet.
      </para>
      <para>
        The following configuration will assign the specified subnet
        identifier to the newly configured subnet:

        <screen>
"Dhcp6": {
    "subnet6": [
        {
            "subnet": "2001:db8:1::/64",
            <userinput>"id": 1024</userinput>,
            ...
        }
    ]
}
</screen>
        This identifier will not change for this subnet unless the "id" parameter is
        removed or set to 0. The value of 0 forces auto-generation of the subnet
        identifier.
      </para>
      <!-- @todo: describe whether database needs to be updated after changing
      id -->
    </section>

    <section id="dhcp6-unicast">
      <title>Unicast Traffic Support</title>
      <para>
        When the DHCPv6 server starts, by default it listens to the DHCP traffic
        sent to multicast address ff02::1:2 on each interface that it is
        configured to listen on (see <xref linkend="dhcp6-interface-selection"/>).
        In some cases it is useful to configure a server to handle incoming
        traffic sent to the global unicast addresses as well. The most common
        reason for this is to have relays send their traffic to the server
        directly. To configure the server to listen on a specific unicast address,
        nn interface name can be
        optionally followed by a slash, followed by the global unicast address on which
        the server should listen. The server listens to this address in addition to normal
        link-local binding and listening on ff02::1:2 address. The sample configuration
        below shows how to listen on 2001:db8::1 (a global address)
        configured on the eth1 interface.
      </para>
      <para>
 <screen>
"Dhcp6": {
    "interfaces-config": {
        "interfaces": [ <userinput>"eth1/2001:db8::1"</userinput> ]
    },
    ...
    "option-data": [
        {
            "name": "unicast",
            "data": "2001:db8::1"
        } ],
    ...
}
 </screen>

        This configuration will cause the server to listen on
        eth1 on the link-local address, the multicast group (ff02::1:2) and 2001:db8::1.
      </para>
      <para>
        Usually unicast support is associated with a server unicast option
        which allows clients to send unicast messages to the server.
        The example above includes a server unicast option specification
        which will cause the client to send messages to the specified
        unicast address.
      </para>
      <para>
        It is possible to mix interface names, wildcards and interface name/addresses
        in the list of interfaces. It is not possible however to specify more than one
        unicast address on a given interface.
      </para>
      <para>
        Care should be taken to specify proper unicast addresses. The server will
        attempt to bind to the addresses specified without any additional checks.
        This approach has selected on purpose to allow the software to
        communicate over uncommon addresses if so desired.
      </para>
    </section>

    <section id="dhcp6-address-config">
      <title>Subnet and Address Pool</title>
      <para>
        The main role of a DHCPv6 server is address assignment. For this,
        the server has to be configured with at least one subnet and one pool of dynamic
        addresses to be managed. For example, assume that the server
        is connected to a network segment that uses the 2001:db8:1::/64
        prefix. The Administrator of that network has decided that addresses from range
        2001:db8:1::1 to 2001:db8:1::ffff are going to be managed by the Dhcp6
        server. Such a configuration can be achieved in the following way:
        <screen>
"Dhcp6": {
    <userinput>"subnet6": [
       {
           "subnet": "2001:db8:1::/64",
           "pools": [
               {
                   "pool": "2001:db8:1::1-2001:db8:1::ffff"
               }
           ],
           ...
       }
    ]</userinput>
}</screen>

        Note that <command>subnet</command> is defined as a simple string, but
        the <command>pools</command> parameter is actually a list of pools: for
        this reason, the pool definition is enclosed in square brackets, even
        though only one range of addresses is specified.</para>

        <para>Each <command>pool</command> is a structure that contains the
        parameters that describe a single pool. Currently there is only one
        parameter, <command>pool</command>, which gives the range of addresses
        in the pool. Additional parameters will be added in future releases of
        Kea.</para>

        <para>It is possible to define more than one pool in a
        subnet: continuing the previous example, further assume that
        2001:db8:1:0:5::/80 should also be managed by the server. It could be written as
        2001:db8:1:0:5:: to 2001:db8:1::5:ffff:ffff:ffff, but typing so many 'f's
        is cumbersome. It can be expressed more simply as 2001:db8:1:0:5::/80. Both
        formats are supported by Dhcp6 and can be mixed in the pool list.
        For example, one could define the following pools:
        <screen>
"Dhcp6": {
    <userinput>"subnet6": [
    {
        "subnet": "2001:db8:1::/64",
        "pools": [
            { "pool": "2001:db8:1::1-2001:db8:1::ffff" },
            { "pool": "2001:db8:1:05::/80" }
        ]</userinput>,
        ...
    }
    ]
}</screen>
        White space in pool definitions is ignored, so spaces before and after the hyphen are optional.
        They can be used to improve readability.
      </para>
      <para>
        The number of pools is not limited, but for performance reasons it is recommended to
        use as few as possible.
      </para>
      <para>
         The server may be configured to serve more than one subnet. To add a second subnet,
         use a command similar to the following:
        <screen>
"Dhcp6": {
    <userinput>"subnet6": [
    {
        "subnet": "2001:db8:1::/64",
        "pools": [
            { "pool": "2001:db8:1::1-2001:db8:1::ffff" }
        ]
    },
    {
        "subnet": "2001:db8:2::/64",
        "pools": [
            { "pool": "2001:db8:2::/64" }
        ]
    },
</userinput>
        ...
    ]
}</screen>
        In this example, we allow the server to
        dynamically assign all addresses available in the whole subnet. Although
        rather wasteful, it is certainly a valid configuration to dedicate the
        whole /64 subnet for that purpose. Note that the Kea server does not preallocate
        the leases, so there is no danger in using gigantic address pools.
      </para>
      <para>
        When configuring a DHCPv6 server using prefix/length notation, please pay
        attention to the boundary values. When specifying that the server can use
        a given pool, it will also be able to allocate the first (typically network
        address) address from that pool. For example, for pool 2001:db8:2::/64 the
        2001:db8:2:: address may be assigned as well. If you want to avoid this,
        use the "min-max" notation.
      </para>
    </section>

    <section>
      <title>Subnet and Prefix Delegation Pools</title>
      <para>
        Subnets may also be configured to delegate prefixes, as defined in
        <ulink url="http://tools.ietf.org/html/rfc3633">RFC 3633</ulink>.  A
        subnet may have one or more prefix delegation pools.  Each pool has a
        prefixed address, which is specified as a prefix
        (<command>prefix</command>) and a prefix length
        (<command>prefix-len</command>), as well as a delegated prefix length
        (<command>delegated-len</command>). The delegated length must not be
        shorter (that is it must be numerically greater or equal) than the
        prefix length.  If both the delegated and prefix lengths are equal, the
        server will be able to delegate only one prefix. The delegated prefix
        does not have to match the subnet prefix.
      </para>
      <para> Below is a sample subnet configuration which enables prefix
      delegation for the subnet:
      <screen>
"Dhcp6": {
    "subnet6": [
        {
            "subnet": "2001:d8b:1::/64",
            <userinput>"pd-pools": [
                {
                    "prefix": "3000:1::",
                    "prefix-len": 64,
                    "delegated-len": 96
                }
            ]</userinput>
        }
    ],
    ...
}</screen>
      </para>

    </section>

    <section id="pd-exclude-option">
        <title>Prefix Exclude Option</title>
        <para>
          For each delegated prefix the delegating router may choose to exclude
          a single prefix out of the delegated prefix as specified in the
          <ulink url="http://tools.ietf.org/html/rfc6603"> RFC 6603</ulink>.
          The requesting router must not assign the excluded prefix to any
          of its downstream interfaces and it is intended to be used on a
          link through which the delegating router exchanges DHCPv6 messages with
          the requesting router. The configuration example below demonstrates how
          to specify an excluded prefix within a prefix pool definition. The
          excluded prefix "2001:db8:1:babe:cafe:80::/72" will be sent to a
          requesting router which includes Prefix Exclude option in the ORO, and
          which is delegated a prefix from this pool.
        </para>
<screen>
"Dhcp6": {
    "subnet6": [
        {
            "subnet": "2001:db8:1::/48",
            "pd-pools": [
                {
                    "prefix": "2001:db8:1:8000::",
                    "prefix-len": 48,
                    "delegated-len": 64,
                    "excluded-prefix": "2001:db8:1:babe:cafe:80::",
                    "excluded-prefix-len": 72
                }
            ]
        }
    ]
}
</screen>
    </section>

    <section id="dhcp6-std-options">
      <title>Standard DHCPv6 Options</title>
      <para>
        One of the major features of a DHCPv6 server is to provide configuration
        options to clients.  Although there are several options that require
        special behavior, most options are sent by the server only if the client
        explicitly requests them.  The following example shows how to
        configure DNS servers, one of the most frequently used
        options.  Options specified in this way are considered
        global and apply to all configured subnets.

        <screen>
"Dhcp6": {
    "option-data": [
        {
           <userinput>"name": "dns-servers",
           "code": 23,
           "space": "dhcp6",
           "csv-format": true,
           "data": "2001:db8::cafe, 2001:db8::babe"</userinput>
        },
        ...
    ]
}
</screen>
      </para>

    <para>
      The <command>option-data</command> line creates a new entry in
      the option-data table.  This table contains
      information on all global options that the server is supposed to configure
      in all subnets.  The <command>name</command> line specifies the option name.
      (For a complete list
      of currently supported names, see <xref
      linkend="dhcp6-std-options-list"/>.)  The next line specifies the option code,
      which must match one of the values from that list. The line beginning with
      <command>space</command> specifies the option space, which must always be set
      to "dhcp6" as these are standard DHCPv6 options.  For other name spaces,
      including custom option spaces, see <xref
      linkend="dhcp6-option-spaces"/>. The following line specifies the format in
      which the data will be entered: use of CSV (comma separated values) is
      recommended. Finally, the <command>data</command> line gives the actual value to be sent to
      clients.  Data is specified as normal text, with values separated by
      commas if more than one value is allowed.
    </para>

    <para>
      Options can also be configured as hexadecimal values.  If "csv-format" is
      set to false, the option data must be specified as a string of hexadecimal
      numbers.  The
      following commands configure the DNS-SERVERS option for all
      subnets with the following addresses: 2001:db8:1::cafe and
      2001:db8:1::babe.
        <screen>
"Dhcp6": {
    "option-data": [
        {
           <userinput>"name": "dns-servers",
           "code": 23,
           "space": "dhcp6",
           "csv-format": false,
           "data": "2001 0DB8 0001 0000 0000 0000 0000 CAFE
                    2001 0DB8 0001 0000 0000 0000 0000 BABE"</userinput>
        },
        ...
    ]
}
</screen>
       </para>
       <note><para>
       The value for the setting of the "data" element is split across two
       lines in this example for clarity: when entering the command, the
       whole string should be entered on the same line.
       </para></note>
       <para>
       Care should be taken
       to use proper encoding when using hexadecimal format as Kea's ability
       to validate data correctness in hexadecimal is limited.
      </para>

      <para>
        Most of the parameters in the "option-data" structure are
        optional and can be omitted in some circumstances as discussed
        in the <xref linkend="dhcp6-option-data-defaults"/>. Only one
        of name or code is required, so you don't need to specify
        both. Space has a default value of "dhcp6", so you can skip
        this as well if you define a regular (not encapsulated) DHCPv6
        option.  Finally, csv-format defaults to true, so it too can
        be skipped, unless you want to specify the option value as
        hexstring. Therefore the above example can be simplified to:
        <screen>
"Dhcp6": {
    "option-data": [
        {
           <userinput>"name": "dns-servers",
           "data": "2001:db8::cafe, 2001:db8::babe"</userinput>
        },
        ...
    ]
}
        </screen>
        Defined options are added to response when the client requests them
        at a few exceptions which are always added. To enforce the addition
        of a particular option set the always-send flag to true as in:
        <screen>
"Dhcp6": {
    "option-data": [
        {
           <userinput>"name": "dns-servers",
           "data": "2001:db8::cafe, 2001:db8::babe",
           "always-send": true</userinput>
        },
        ...
    ]
}
        </screen>
        The effect is the same as if the client added the option code in the
        Option Request Option (or its equivalent for vendor options) so in:
        <screen>
"Dhcp6": {
    "option-data": [
        {
           <userinput>"name": "dns-servers",
           "data": "2001:db8::cafe, 2001:db8::babe",
           "always-send": true</userinput>
        },
        ...
    ],
    "subnet6": [
        {
           "subnet": "2001:db8:1::/64",
           "option-data": [
               {
                   <userinput>"name": "dns-servers",
                   "data": "2001:db8:1::cafe, 2001:db8:1::babe"</userinput>
               },
               ...
           ],
           ...
        },
        ...
    ],
    ...
}
        </screen>
        The DNS Servers option is always added to responses
        (the always-send is "sticky") but the value is the subnet one
        when the client is localized in the subnet.
      </para>

    <para>
      It is possible to override options on a per-subnet basis.  If
      clients connected to most of your subnets are expected to get the
      same values of a given option, you should use global options: you
      can then override specific values for a small number of subnets.
      On the other hand, if you use different values in each subnet,
      it does not make sense to specify global option values
      (Dhcp6/option-data), rather you should set only subnet-specific values
      (Dhcp6/subnet[X]/option-data[Y]).
     </para>

     <para>
      The following commands override the global
      DNS servers option for a particular subnet, setting a single DNS
      server with address 2001:db8:1::3.
<screen>
"Dhcp6": {
    "subnet6": [
        {
            <userinput>"option-data": [
                {
                    "name": "dns-servers",
                    "code": 23,
                    "space": "dhcp6",
                    "csv-format": true,
                    "data": "2001:db8:1::3"
                },
                ...
            ]</userinput>,
            ...
        },
        ...
    ],
    ...
}
</screen>
    </para>

     <para>
       In some cases it is useful to associate some options with an
       address or prefix pool from which a client is assigned a lease. Pool
       specific option values override subnet specific and global option
       values. If the client is assigned multiple leases from different
       pools, the server will assign options from all pools from which the
       leases have been obtained. However, if the particular option is specified
       in multiple pools from which the client obtains the leases, only one
       instance of this option will be handed out to the client. The server's
       administrator must not try to prioritize assignment of pool specific
       options by trying to order pools declarations in the server
       configuration. Future Kea releases may change the order in which
       options are assigned from the pools without any notice.
     </para>

     <para>
       The following configuration snippet demonstrates how to specify the
       DNS servers option, which will be assigned to a client only if the
       client obtains an address from the given pool:
<screen>
"Dhcp6": {
    "subnet6": [
        {
            "pools": [
                {
                    "pool": "2001:db8:1::100-2001:db8:1::300",
                    <userinput>"option-data": [
                        {
                            "name": "dns-servers",
                            "data": "2001:db8:1::10"
                        }
                    ]</userinput>
                }
            ]
        },
        ...
    ],
    ...
}
</screen>
     </para>

    <para>
      The currently supported standard DHCPv6 options are
      listed in <xref linkend="dhcp6-std-options-list"/>.
      The "Name" and "Code"
      are the values that should be used as a name in the option-data
      structures. "Type" designates the format of the data: the meanings of
      the various types is given in <xref linkend="dhcp-types"/>.
    </para>
    <para>
      Experimental options (like standard options but with a code
      which was not assigned by IANA) are listed in
      <xref linkend="dhcp6-exp-options-list"/>.
    </para>
    <para>When a data field is a string, and that string contains
    the comma (,; U+002C) character, the comma must be escaped with a
    reverse solidus character (\; U+005C). This double escape is
    required, because both the routine splitting CSV data into fields
    and JSON use the same escape character: a single escape (\,) would
    make the JSON invalid. For example, the string
    &quot;EST5EDT4,M3.2.0/02:00,M11.1.0/02:00&quot; would be
    represented as:
<screen>
"Dhcp6": {
    "subnet6": [
        {
            "pools": [
                {
                    <userinput>"option-data": [
                        {
                            "name": "new-posix-timezone",
                            "data": "EST5EDT4\,M3.2.0/02:00\,M11.1.0/02:00"
                        }
                    ]</userinput>
                },
                ...
            ],
            ...
        },
        ...
    ],
    ...
}
</screen>
    </para>
    <para>
      Some options are designated as arrays, which means that more than one
      value is allowed in such an option. For example the option dns-servers
      allows the specification of more than one IPv6 address, allowing
      clients to obtain the addresses of multiple DNS servers.
    </para>

<!-- @todo: describe record types -->
<!-- @todo: describe array in record types -->

      <para>
        The <xref linkend="dhcp6-custom-options"/> describes the configuration
        syntax to create custom option definitions (formats). It is generally not
        allowed to create custom definitions for standard options, even if the
        definition being created matches the actual option format defined in the
        RFCs. There is an exception from this rule for standard options for which
        Kea does not yes provide a definition. In order to use such options,
        a server administrator must create a definition as described in
        <xref linkend="dhcp6-custom-options"/> in the 'dhcp6' option space. This
        definition should match the option format described in the relevant
        RFC but the configuration mechanism would allow any option format as it has
        no means to validate the format at the moment.
      </para>


    <para>
      <table frame="all" id="dhcp6-std-options-list">
        <title>List of Standard DHCPv6 Options</title>
        <tgroup cols='4'>
        <colspec colname='name'/>
        <colspec colname='code' align='center'/>
        <colspec colname='type' align='center'/>
        <colspec colname='array' align='center'/>
        <thead>
          <row><entry>Name</entry><entry>Code</entry><entry>Type</entry><entry>Array?</entry></row>
        </thead>
        <tbody>
<!-- Our engine uses those options on its own, admin must not configure them on his own
<row><entry>clientid</entry><entry>1</entry><entry>binary</entry><entry>false</entry></row>
<row><entry>serverid</entry><entry>2</entry><entry>binary</entry><entry>false</entry></row>
<row><entry>ia-na</entry><entry>3</entry><entry>record</entry><entry>false</entry></row>
<row><entry>ia-ta</entry><entry>4</entry><entry>uint32</entry><entry>false</entry></row>
<row><entry>iaaddr</entry><entry>5</entry><entry>record</entry><entry>false</entry></row>
<row><entry>oro</entry><entry>6</entry><entry>uint16</entry><entry>true</entry></row> -->
<row><entry>preference</entry><entry>7</entry><entry>uint8</entry><entry>false</entry></row>

<!-- Our engine uses those options on its own, admin must not configure them on his own
<row><entry>elapsed-time</entry><entry>8</entry><entry>uint16</entry><entry>false</entry></row>
<row><entry>relay-msg</entry><entry>9</entry><entry>binary</entry><entry>false</entry></row>
<row><entry>auth</entry><entry>11</entry><entry>binary</entry><entry>false</entry></row>
-->
<row><entry>unicast</entry><entry>12</entry><entry>ipv6-address</entry><entry>false</entry></row>
<!--
<row><entry>status-code</entry><entry>13</entry><entry>record</entry><entry>false</entry></row>
<row><entry>rapid-commit</entry><entry>14</entry><entry>empty</entry><entry>false</entry></row>
<row><entry>user-class</entry><entry>15</entry><entry>binary</entry><entry>false</entry></row>
<row><entry>vendor-class</entry><entry>16</entry><entry>record</entry><entry>false</entry></row>
-->
<!-- Vendor-specific Information is configurable by the administrator -->
<row><entry>vendor-opts</entry><entry>17</entry><entry>uint32</entry><entry>false</entry></row>
<!--
<row><entry>interface-id</entry><entry>18</entry><entry>binary</entry><entry>false</entry></row>
<row><entry>reconf-msg</entry><entry>19</entry><entry>uint8</entry><entry>false</entry></row>
<row><entry>reconf-accept</entry><entry>20</entry><entry>empty</entry><entry>false</entry></row> -->
-->
<row><entry>sip-server-dns</entry><entry>21</entry><entry>fqdn</entry><entry>true</entry></row>
<row><entry>sip-server-addr</entry><entry>22</entry><entry>ipv6-address</entry><entry>true</entry></row>
<row><entry>dns-servers</entry><entry>23</entry><entry>ipv6-address</entry><entry>true</entry></row>
<row><entry>domain-search</entry><entry>24</entry><entry>fqdn</entry><entry>true</entry></row>
<!-- <row><entry>ia-pd</entry><entry>25</entry><entry>record</entry><entry>false</entry></row> -->
<!-- <row><entry>iaprefix</entry><entry>26</entry><entry>record</entry><entry>false</entry></row> -->
<row><entry>nis-servers</entry><entry>27</entry><entry>ipv6-address</entry><entry>true</entry></row>
<row><entry>nisp-servers</entry><entry>28</entry><entry>ipv6-address</entry><entry>true</entry></row>
<row><entry>nis-domain-name</entry><entry>29</entry><entry>fqdn</entry><entry>true</entry></row>
<row><entry>nisp-domain-name</entry><entry>30</entry><entry>fqdn</entry><entry>true</entry></row>
<row><entry>sntp-servers</entry><entry>31</entry><entry>ipv6-address</entry><entry>true</entry></row>
<row><entry>information-refresh-time</entry><entry>32</entry><entry>uint32</entry><entry>false</entry></row>
<row><entry>bcmcs-server-dns</entry><entry>33</entry><entry>fqdn</entry><entry>true</entry></row>
<row><entry>bcmcs-server-addr</entry><entry>34</entry><entry>ipv6-address</entry><entry>true</entry></row>
<row><entry>geoconf-civic</entry><entry>36</entry><entry>record (uint8, uint16, binary)</entry><entry>false</entry></row>
<row><entry>remote-id</entry><entry>37</entry><entry>record (uint32, binary)</entry><entry>false</entry></row>
<row><entry>subscriber-id</entry><entry>38</entry><entry>binary</entry><entry>false</entry></row>
<row><entry>client-fqdn</entry><entry>39</entry><entry>record (uint8, fqdn)</entry><entry>false</entry></row>
<row><entry>pana-agent</entry><entry>40</entry><entry>ipv6-address</entry><entry>true</entry></row>
<row><entry>new-posix-timezone</entry><entry>41</entry><entry>string</entry><entry>false</entry></row>
<row><entry>new-tzdb-timezone</entry><entry>42</entry><entry>string</entry><entry>false</entry></row>
<row><entry>ero</entry><entry>43</entry><entry>uint16</entry><entry>true</entry></row>
<row><entry>lq-query</entry><entry>44</entry><entry>record (uint8, ipv6-address)</entry><entry>false</entry></row>
<row><entry>client-data</entry><entry>45</entry><entry>empty</entry><entry>false</entry></row>
<row><entry>clt-time</entry><entry>46</entry><entry>uint32</entry><entry>false</entry></row>
<row><entry>lq-relay-data</entry><entry>47</entry><entry>record (ipv6-address, binary)</entry><entry>false</entry></row>
<row><entry>lq-client-link</entry><entry>48</entry><entry>ipv6-address</entry><entry>true</entry></row>
<row><entry>v6-lost</entry><entry>51</entry><entry>fqdn</entry><entry>false</entry></row>
<row><entry>capwap-ac-v6</entry><entry>52</entry><entry>ipv6-address</entry><entry>true</entry></row>
<row><entry>relay-id</entry><entry>53</entry><entry>binary</entry><entry>false</entry></row>
<row><entry>v6-access-domain</entry><entry>57</entry><entry>fqdn</entry><entry>false</entry></row>
<row><entry>sip-ua-cs-list</entry><entry>58</entry><entry>fqdn</entry><entry>true</entry></row>
<row><entry>bootfile-url</entry><entry>59</entry><entry>string</entry><entry>false</entry></row>
<row><entry>bootfile-param</entry><entry>60</entry><entry>tuple</entry><entry>true</entry></row>
<row><entry>client-arch-type</entry><entry>61</entry><entry>uint16</entry><entry>true</entry></row>
<row><entry>nii</entry><entry>62</entry><entry>record (uint8, uint8, uint8)</entry><entry>false</entry></row>
<row><entry>aftr-name</entry><entry>64</entry><entry>fqdn</entry><entry>false</entry></row>
<row><entry>erp-local-domain-name</entry><entry>65</entry><entry>fqdn</entry><entry>false</entry></row>
<row><entry>rsoo</entry><entry>66</entry><entry>empty</entry><entry>false</entry></row>
<row><entry>pd-exclude</entry><entry>67</entry><entry>binary</entry><entry>false</entry></row>
<row><entry>rdnss-selection</entry><entry>74</entry><entry>record (ipv6-address, uint8, fqdn)</entry><entry>true</entry></row>
<row><entry>client-linklayer-addr</entry><entry>79</entry><entry>binary</entry><entry>false</entry></row>
<row><entry>link-address</entry><entry>80</entry><entry>ipv6-address</entry><entry>false</entry></row>
<row><entry>solmax-rt</entry><entry>82</entry><entry>uint32</entry><entry>false</entry></row>
<row><entry>inf-max-rt</entry><entry>83</entry><entry>uint32</entry><entry>false</entry></row>
<!-- <row><entry>dhcpv4-message</entry><entry>87</entry><entry>binary</entry><entry>false</entry></row> -->
<row><entry>dhcp4o6-server-addr</entry><entry>88</entry><entry>ipv6-address</entry><entry>true</entry></row>
<row><entry>v6-captive-portal</entry><entry>103</entry><entry>string</entry><entry>false</entry></row>
<row><entry>ipv6-address-andsf</entry><entry>143</entry><entry>ipv6-address</entry><entry>true</entry></row>
        </tbody>
        </tgroup>
      </table>
    </para>

    <para>
      <table frame="all" id="dhcp6-exp-options-list">
        <title>List of Experimental DHCPv6 Options</title>
        <tgroup cols='4'>
        <colspec colname='name'/>
        <colspec colname='code' align='center'/>
        <colspec colname='type' align='center'/>
        <colspec colname='array' align='center'/>
        <thead>
          <row><entry>Name</entry><entry>Code</entry><entry>Type</entry><entry>Array?</entry></row>
        </thead>
        <tbody>
<row><entry>public-key</entry><entry>701</entry><entry>binary</entry><entry>false</entry></row>
<row><entry>certificate</entry><entry>702</entry><entry>binary</entry><entry>false</entry></row>
<row><entry>signature</entry><entry>703</entry><entry>record (uint8, uint8, binary)</entry><entry>false</entry></row>
<row><entry>timestamp</entry><entry>704</entry><entry>binary</entry><entry>false</entry></row>
        </tbody>
        </tgroup>
      </table>
    </para>
    </section>

    <section id="dhcp6-custom-options">
      <title>Custom DHCPv6 Options</title>
      <para>It is possible to define options in addition to the standard ones.
      Assume that we want to define a new DHCPv6 option called "foo" which will have
      code 100 and which will convey a single unsigned 32 bit integer value. We can define
      such an option by using the following commands:
<screen>
"Dhcp6": {
    "option-def": [
        {
            <userinput>"name": "foo",
            "code": 100,
            "type": "uint32",
            "array": false,
            "record-types": "",
            "space": "dhcp6",
            "encapsulate": ""</userinput>
        }, ...
    ],
    ...
}
</screen>
      The "false" value of the <command>array</command> parameter determines that the option does
      NOT comprise an array of "uint32" values but rather a single value.  Two
      other parameters have been left blank: <command>record-types</command> and
      <command>encapsulate</command>.
      The former specifies the comma separated list of option data fields if the
      option comprises a record of data fields. The <command>record-types</command> value should
      be non-empty if the <command>type</command> is set to "record". Otherwise it must be left
      blank. The latter parameter specifies the name of the option space being
      encapsulated by the particular option. If the particular option does not
      encapsulate any option space it should be left blank.  Note that the above
      example only defines the format of the new option, it does not set its
      value(s).
      </para>

      <para>The <command>name</command>, <command>code</command> and
      <command>type</command> parameters are required, all others are
      optional. The <command>array</command> default value is
      <command>false</command>. The <command>record-types</command>
      and <command>encapsulate</command> default values are blank
      (i.e. ""). The default <command>space</command> is "dhcp6".
      </para>

      <para>Once the new option format is defined, its value is set
      in the same way as for a standard option. For example the following
      commands set a global value that applies to all subnets.
<screen>
"Dhcp6": {
    "option-data": [
        {
            <userinput>"name": "foo",
            "code": 100,
            "space": "dhcp6",
            "csv-format": true,
            "data": "12345"</userinput>
        }, ...
    ],
    ...
}
</screen>
      </para>

      <para>New options can take more complex forms than simple use of
      primitives (uint8, string, ipv6-address etc): it is possible to
      define an option comprising a number of existing primitives.
      </para>
      <para>
      For example, assume we want to define a new option that will consist of an IPv6
      address, followed by an unsigned 16 bit integer, followed by a
      boolean value, followed by a text string. Such an option could
      be defined in the following way:
<screen>
"Dhcp6": {
    "option-def": [
        {
            <userinput>"name": "bar",
            "code": 101,
            "space": "dhcp6",
            "type": "record",
            "array": false,
            "record-types": "ipv6-address, uint16, boolean, string",
            "encapsulate": ""</userinput>
        }, ...
    ],
    ...
}
</screen>
      The "type" is set to "record" to indicate that the option contains
      multiple values of different types.  These types are given as a comma-separated
      list in the "record-types" field and should be those listed in <xref linkend="dhcp-types"/>.
      </para>
      <para>
      The values of the option are set as follows:
<screen>
"Dhcp6": {
    "option-data": [
        {
            <userinput>"name": "bar",
            "space": "dhcp6",
            "code": 101,
            "csv-format": true,
            "data": "2001:db8:1::10, 123, false, Hello World"</userinput>
        }
    ],
    ...
}</screen>

      <command>csv-format</command> is set <command>true</command> to indicate
      that the <command>data</command> field comprises a command-separated list
      of values.  The values in the "data" must correspond to the types set in
      the "record-types" field of the option definition.
      </para>

      <para>
      When <command>array</command> is set to <command>true</command>
      and <command>type</command> is set to "record", the last field
      is an array, i.e., it can contain more than one value as in:
<screen>
"Dhcp6": {
    "option-def": [
        {
            <userinput>"name": "bar",
            "code": 101,
            "space": "dhcp6",
            "type": "record",
            "array": true,
            "record-types": "ipv6-address, uint16",
            "encapsulate": ""</userinput>
        }, ...
    ],
    ...
}
</screen>
      The new option content is one IPv6 address followed by one or more 16
      bit unsigned integers.
      </para>

      <note>
       <para>In the general case, boolean values are specified as <command>true</command> or
       <command>false</command>, without quotes. Some specific boolean parameters may
       accept also <command>"true"</command>, <command>"false"</command>,
       <command>0</command>, <command>1</command>, <command>"0"</command> and
       <command>"1"</command>. Future versions of Kea will accept all those values
       for all boolean parameters.</para>
      </note>

    </section>

    <section id="dhcp6-vendor-opts">
      <title>DHCPv6 Vendor-Specific Options</title>
      <para>
      Currently there are two option spaces defined for the DHCPv6
      daemon: "dhcp6" (for top level DHCPv6 options) and "vendor-opts-space",
      which is empty by default, but in which options can be defined.
      Those options will be carried in the Vendor-Specific
      Information option (code 17). The following examples show how to
      define an option "foo" with code 1 that consists of an IPv6 address,
      an unsigned 16 bit integer and a string. The "foo" option is
      conveyed in a Vendor-Specific Information option. This option
      comprises a single uint32 value that is set to "12345".
      The sub-option "foo" follows the data field holding this value.
      <screen>
"Dhcp6": {
    "option-def": [
        {
            <userinput>"name": "foo",
            "code": 1,
            "space": "vendor-opts-space",
            "type": "record",
            "array": false,
            "record-types": "ipv6-address, uint16, string",
            "encapsulate": ""</userinput>
        }
    ],
    ...
}</screen>
     (Note that the option space is set to <command>vendor-opts-space</command>.)
     Once the option format is defined, the next step is to define actual values
     for that option:
<screen>
"Dhcp6": {
    "option-data": [
        {
            <userinput>"name": "foo",
            "space": "vendor-opts-space",
            "data": "2001:db8:1::10, 123, Hello World"</userinput>
        },
        ...
    ],
    ...
}</screen>
    We should also define a value (enterprise-number) for the
    Vendor-specific Information option, that conveys our option "foo".
<screen>
"Dhcp6": {
    "option-data": [
        ...,
        {
            <userinput>"name": "vendor-opts",
            "data": "12345"</userinput>
        }
    ],
    ...
}</screen>
    Alternatively, the option can be specified using its code.
<screen>
"Dhcp6": {
    "option-data": [
        ...,
        {
            <userinput>"code": 17,
            "data": "12345"</userinput>
        }
    ],
    ...
}</screen>
      </para>
    </section>

    <section id="dhcp6-option-spaces">
      <title>Nested DHCPv6 Options (Custom Option Spaces)</title>
      <para>It is sometimes useful to define completely new option
      spaces.  This is useful if the user wants their new option to
      convey sub-options that use a separate numbering scheme, for
      example sub-options with codes 1 and 2. Those option codes
      conflict with standard DHCPv6 options, so a separate option
      space must be defined.
      </para>
      <para>Note that it is not required to create a new option space when
      defining sub-options for a standard option because it is
      created by default if the standard option is meant to convey
      any sub-options (see <xref linkend="dhcp6-vendor-opts"/>).
      </para>
      <para>
      Assume that we want to have a DHCPv6 option called "container"
      with code 102 that conveys two sub-options with codes 1 and 2.
      First we need to define the new sub-options:
<screen>
"Dhcp6": {
    "option-def": [
        {
            <userinput>"name": "subopt1",
            "code": 1,
            "space": "isc",
            "type": "ipv6-address",
            "record-types": "",
            "array": false,
            "encapsulate": ""</userinput>
        },
        {
            <userinput>"name": "subopt2",
            "code": 2,
            "space": "isc",
            "type": "string",
            "record-types": "",
            "array": false
            "encapsulate": ""</userinput>
        }
    ],
    ...
}</screen>
    Note that we have defined the options to belong to a new option space
    (in this case, "isc").
    </para>
    <para>
The next step is to define a regular DHCPv6 option and specify that it
should include options from the isc option space:
<screen>
"Dhcp6": {
    "option-def": [
        ...,
        {
            <userinput>"name": "container",
            "code": 102,
            "space": "dhcp6",
            "type": "empty",
            "array": false,
            "record-types": "",
            "encapsulate": "isc"</userinput>
        }
    ],
    ...
}</screen>

    The name of the option space in which the sub-options are defined is set in
    the <command>encapsulate</command> field. The <command>type</command> field
    is set to <command>empty</command> which limits this option to only carrying
    data in sub-options.
    </para>
    <para>
    Finally, we can set values for the new options:
<screen>
"Dhcp6": {
    "option-data": [
        {
            <userinput>"name": "subopt1",
            "code": 1,
            "space": "isc",
            "data": "2001:db8::abcd"</userinput>
        },
        }
            <userinput>"name": "subopt2",
            "code": 2,
            "space": "isc",
            "data": "Hello world"</userinput>
        },
        {
            <userinput>"name": "container",
            "code": 102,
            "space": "dhcp6"</userinput>
        }
    ],
    ...
}
</screen>
    </para>

    <para>Note that it is possible to create an option which carries some data
    in addition to the sub-options defined in the encapsulated option space.
    For example, if the "container" option from the previous example was
    required to carry an uint16 value as well as the sub-options, the "type"
    value would have to be set to "uint16" in the option definition. (Such an
    option would then have the following data structure: DHCP header, uint16
    value, sub-options.) The value specified with the "data" parameter &mdash; which
    should be a valid integer enclosed in quotes, e.g. "123" &mdash; would then be
    assigned to the uint16 field in the "container" option.
    </para>
    </section>

    <section id="dhcp6-option-data-defaults">
      <title>Unspecified Parameters for DHCPv6 Option Configuration</title>
      <para>In many cases it is not required to specify all parameters for
      an option configuration and the default values can be used. However, it is
      important to understand the implications of not specifying some of them
      as it may result in configuration errors. The list below explains
      the behavior of the server when a particular parameter is not explicitly
      specified:

      <itemizedlist>
        <listitem>
          <simpara><command>name</command> - the server requires an option name or
          option code to identify an option. If this parameter is unspecified, the
          option code must be specified.
          </simpara>
        </listitem>

        <listitem>
          <simpara><command>code</command> - the server requires an option name or
          option code to identify an option. This parameter may be left unspecified if
          the <command>name</command> parameter is specified. However, this also
          requires that the particular option has its definition (it is either a
          standard option or an administrator created a definition for the option
          using an 'option-def' structure), as the option definition associates an
          option with a particular name. It is possible to configure an option
          for which there is no definition (unspecified option format).
          Configuration of such options requires the use of option code.
          </simpara>
        </listitem>

        <listitem>
          <simpara><command>space</command> - if the option space is unspecified it
          will default to 'dhcp6' which is an option space holding DHCPv6 standard
          options.
          </simpara>
        </listitem>

        <listitem>
          <simpara><command>data</command> - if the option data is unspecified it
          defaults to an empty value. The empty value is mostly used for the
          options which have no payload (boolean options), but it is legal to specify
          empty values for some options which carry variable length data and which
          spec allows for the length of 0. For such options, the data parameter
          may be omitted in the configuration.</simpara>
        </listitem>

        <listitem>
          <simpara><command>csv-format</command> - if this value is not
          specified the server will assume that the option data is specified as
          a list of comma separated values to be assigned to individual fields
          of the DHCP option. This behavior has changed in Kea 1.2. Older
          versions used additional logic to determine whether the csv-format
          should be true or false. That is no longer the case.
          </simpara>
        </listitem>
      </itemizedlist>
      </para>

    </section>

    <section id="dhcp6-config-subnets">
      <title>IPv6 Subnet Selection</title>
      <para>
        The DHCPv6 server may receive requests from local (connected to the
        same subnet as the server) and remote (connecting via relays) clients.
        As the server may have many subnet configurations defined, it must select
        an appropriate subnet for a given request.
      </para>
      <para>
        The server can not assume which of the configured subnets are local. In IPv4
        it is possible as there is a reasonable expectation that the
        server will have a (global) IPv4 address configured on the interface,
        and can use that information to detect whether a subnet is local or
        not. That assumption is not true in IPv6: the DHCPv6 server must be able
        to operate while only using link-local addresses. Therefore an optional
        <command>interface</command> parameter is available within a subnet definition
        to designate that a given subnet is local, i.e. reachable directly over
        the specified interface. For example the server that is intended to serve
        a local subnet over eth0 may be configured as follows:
        <screen>
"Dhcp6": {
    "subnet6": [
        {
            "subnet": "2001:db8:beef::/48",
            "pools": [
                 {
                     "pool": "2001:db8:beef::/48"
                 }
             ],
            <userinput>"interface": "eth0"</userinput>
        }
    ],
    ...
}
</screen>
        </para>
      </section>

      <section id="dhcp6-rapid-commit">
        <title>Rapid Commit</title>
        <para>The Rapid Commit option, described in
        <ulink url="http://tools.ietf.org/html/rfc3315">RFC 3315</ulink>, is supported
        by the Kea DHCPv6 server. However, support is disabled by default for
        all subnets. It can be enabled for a particular subnet using the
        <command>rapid-commit</command> parameter as shown below:
<screen>
"Dhcp6": {
    "subnet6": [
        {
            "subnet": "2001:db8:beef::/48",
            <userinput>"rapid-commit": true</userinput>,
            "pools": [
                 {
                     "pool": "2001:db8:beef::1-2001:db8:beef::10"
                 }
             ],
        }
    ],
    ...
}
</screen>
        </para>
        <para>
          This setting only affects the subnet for which the
          <command>rapid-commit</command> is set to <command>true</command>.
          For clients connected to other subnets, the server will ignore the
          Rapid Commit option sent by the client and will follow the 4-way
          exchange procedure, i.e. respond with an Advertise for a Solicit
          containing a Rapid Commit option.
        </para>
      </section>

      <section id="dhcp6-relays">
        <title>DHCPv6 Relays</title>
        <para>
          A DHCPv6 server with multiple subnets defined must select the
          appropriate subnet when it receives a request from a client.  For clients
          connected via relays, two mechanisms are used:
        </para>
        <para>
          The first uses the linkaddr field in the RELAY_FORW message. The name
          of this field is somewhat misleading in that it does not contain a link-layer
          address: instead, it holds an address (typically a global address) that is
          used to identify a link. The DHCPv6 server checks if the address belongs
          to a defined subnet and, if it does, that subnet is selected for the client's
          request.
        </para>
        <para>
          The second mechanism is based on interface-id options. While forwarding a client's
          message, relays may insert an interface-id option into the message that
          identifies the interface on the relay that received the message. (Some
          relays allow configuration of that parameter, but it is sometimes
          hardcoded and may range from the very simple (e.g. "vlan100") to the very cryptic:
          one example seen on real hardware was "ISAM144|299|ipv6|nt:vp:1:110"). The
          server can use this information to select the appropriate subnet.
          The information is also returned to the relay which then knows the
          interface to use to transmit the response to the client. In order for
          this to work successfully, the relay interface IDs must be unique within
          the network and the server configuration must match those values.
        </para>
        <para>
          When configuring the DHCPv6 server, it should be noted that two
          similarly-named parameters can be configured for a subnet:
          <itemizedlist>
            <listitem><simpara>
              <command>interface</command> defines which local network interface can be used
              to access a given subnet.
            </simpara></listitem>
            <listitem><simpara>
              <command>interface-id</command> specifies the content of the interface-id option
              used by relays to identify the interface on the relay to which
              the response packet is sent.
            </simpara></listitem>
          </itemizedlist>
          The two are mutually exclusive: a subnet cannot be both reachable locally
          (direct traffic) and via relays (remote traffic). Specifying both is a
          configuration error and the DHCPv6 server will refuse such a configuration.
        </para>

        <para>
          The following example configuration shows how to specify an interface-id with
          a value of "vlan123".
          <screen>
"Dhcp6": {
    "subnet6": [
        {
            "subnet": "2001:db8:beef::/48",
            "pools": [
                 {
                     "pool": "2001:db8:beef::/48"
                 }
             ],
            <userinput>"interface-id": "vlan123"</userinput>
        }
    ],
    ...
}
</screen>
        </para>
      </section>

    <section id="dhcp6-rsoo">
      <title>Relay-Supplied Options</title>
      <para><ulink url="http://tools.ietf.org/html/rfc6422">RFC 6422</ulink>
      defines a mechanism called Relay-Supplied DHCP Options. In certain cases relay
      agents are the only entities that may have specific information. They can
      insert options when relaying messages from the client to the server. The
      server will then do certain checks and copy those options to the response
      that will be sent to the client.</para>

      <para>There are certain conditions that must be met for the option to be
      included. First, the server must not provide the option itself. In
      other words, if both relay and server provide an option, the server always
      takes precedence. Second, the option must be RSOO-enabled. IANA maintains a
      list of RSOO-enabled options <ulink url="http://www.iana.org/assignments/dhcpv6-parameters/dhcpv6-parameters.xhtml#options-relay-supplied">here</ulink>.
      However, there may be cases when system administrators want to echo other
      options. Kea can be instructed to treat other options as RSOO-enabled.
      For example, to mark options 110, 120 and 130 as RSOO-enabled, the following
      syntax should be used:
<screen>
"Dhcp6": {
    <userinput>"relay-supplied-options": [ "110", "120", "130" ],</userinput>
    ...
}
</screen>
      </para>
      <para>As of March 2015, only option 65 is RSOO-enabled by IANA. This
      option will always be treated as such and there's no need to explicitly
      mark it. Also, when enabling standard options, it is possible to use their
      names, rather than option code, e.g. (e.g. use
      <command>dns-servers</command> instead of <command>23</command>). See
      <xref linkend="dhcp6-std-options-list" /> for the names. In certain cases
      it could also work for custom options, but due to the nature of the parser
      code this may be unreliable and should be avoided.
      </para>

    </section>

    <section id="dhcp6-client-classifier">
      <title>Client Classification in DHCPv6</title>

      <para>
      The DHCPv6 server includes support for client classification.  For a deeper
      discussion of the classification process see <xref linkend="classify"/>.
      </para>

      <para>
      In certain cases it is useful to differentiate between different types
      of clients and treat them accordingly. It is envisaged that client
      classification will be used for changing the behavior of almost any part of
      the DHCP message processing, including the assignment of leases from different
      pools, the assignment of different options (or different values of the same
      options) etc. In the current release of the software however, there are
      only two mechanisms that take advantage of client classification:
      subnet selection and assignment of different options.
      </para>

      <para>
      Kea can be instructed to limit access to given subnets based on class information.
      This is particularly useful for cases where two types of devices share the
      same link and are expected to be served from two different subnets. The
      primary use case for such a scenario is cable networks. Here, there are two
      classes of devices: the cable modem itself, which should be handed a lease
      from subnet A and all other devices behind the modem that should get a lease
      from subnet B. That segregation is essential to prevent overly curious
      users from playing with their cable modems. For details on how to set up
      class restrictions on subnets, see <xref linkend="classification-subnets"/>.
      </para>

      <para>
      The process of doing classification is conducted in three steps. The first step
      is to assess an incoming packet and assign it to zero or more classes.  The
      second step is to choose a subnet, possibly based on the class information.
      The third step is to assign options again possibly based on the class
      information.
      </para>

      <para>
      There are two methods of doing classification. The first is automatic and relies
      on examining the values in the vendor class options. Information from these
      options is extracted and a class name is constructed from it and added to
      the class list for the packet. The second allows you to specify an expression
      that is evaluated for each packet. If the result is true the packet is
      a member of the class.
      </para>

      <note><para>
        Care should be taken with client classification as it is easy for
        clients that do not meet class criteria to be denied any service altogether.
      </para></note>

      <section>
        <title>Defining and Using Custom Classes</title>
        <para>
        The following example shows how to configure a class using an expression
        and a subnet making use of that class. This configuration defines the
        class named &quot;Client_enterprise&quot;. It is comprised
        of all clients whose client identifiers start with the given hex string (which
        would indicate a DUID based on an enterprise id of 0xAABBCCDD).
        They will be given an address from 2001:db8:1::0 to 2001:db8:1::FFFF and
        the addresses of their DNS servers set to 2001:db8:0::1 and 2001:db8:2::1.

        <screen>
"Dhcp6": {
    "client-classes": [
        {<userinput>
            "name": "Client_enterprise",
            "test": "substring(option[1].hex,0,6) == 0x0002AABBCCDD'",
            "option-data": [
                {
                    "name": "dns-servers",
                    "code": 23,
                    "space": "dhcp6",
                    "csv-format": true,
                    "data": "2001:db8:0::1, 2001:db8:2::1"
                }
            ]</userinput>
        },
        ...
    ],
    "subnet6": [
        {
            "subnet": "2001:db8:1::/64",
            "pools": [ { "pool": "2001:db8:1::-2001:db8:1::ffff" } ],
            <userinput>"client-class": "Client_enterprise"</userinput>
        }
    ],
    ...
}</screen>
      </para>

      <para>
      This example shows a configuration using an automatically generated
      "VENDOR_CLASS_" class. The Administrator of the network has
      decided that addresses from range 2001:db8:1::1 to 2001:db8:1::ffff are
      going to be managed by the Dhcp6 server and only clients belonging to the
      eRouter1.0 client class are allowed to use that pool.

        <screen>
"Dhcp6": {
    "subnet6": [
        {
            "subnet": "2001:db8:1::/64",
            "pools": [
                 {
                     "pool": "2001:db8:1::-2001:db8:1::ffff"
                 }
             ],
            <userinput>"client-class": "VENDOR_CLASS_eRouter1.0"</userinput>
        }
    ],
    ...
}
</screen>
        </para>
      </section>
    </section>

    <section id="dhcp6-ddns-config">
      <title>DDNS for DHCPv6</title>
      <para>
      As mentioned earlier, kea-dhcp6 can be configured to generate requests to
      the DHCP-DDNS server (referred to here as "D2") to update
      DNS entries.  These requests are known as NameChangeRequests or NCRs.
      Each NCR contains the following information:
      <orderedlist>
      <listitem><para>
      Whether it is a request to add (update) or remove DNS entries
      </para></listitem>
      <listitem><para>
      Whether the change requests forward DNS updates (AAAA records), reverse
      DNS updates (PTR records), or both.
      </para></listitem>
      <listitem><para>
      The FQDN, lease address, and DHCID
      </para></listitem>
      </orderedlist>
      The parameters controlling the generation of NCRs for submission to D2
      are contained in the <command>dhcp-ddns</command> section of the kea-dhcp6
      configuration. The mandatory parameters for the DHCP DDNS configuration
      are <command>enable-updates</command> which is unconditionally
      required, and <command>qualifying-suffix</command> which has no
      default value and is required when <command>enable-updates</command>
      is set to <command>true</command>.

      The two (disabled and enabled) minimal DHCP DDNS configurations are:
<screen>
"Dhcp6": {
    "dhcp-ddns": {
        <userinput>"enable-updates": false</userinput>
    },
    ...
}
</screen>
      and for example:
<screen>
"Dhcp6": {
    "dhcp-ddns": {
        <userinput>"enable-updates": true,
        "qualifying-suffix": "example."</userinput>
    },
    ...
}
</screen>

      The default values for the "dhcp-ddns" section are as follows:
      <itemizedlist>
      <listitem><simpara>
      <command>"server-ip": "127.0.0.1"</command>
      </simpara></listitem>
      <listitem><simpara>
      <command>"server-port": 53001</command>
      </simpara></listitem>
      <listitem><simpara>
      <command>"sender-ip": ""</command>
      </simpara></listitem>
      <listitem><simpara>
      <command>"sender-port": 0</command>
      </simpara></listitem>
      <listitem><simpara>
      <command>"max-queue-size": 1024</command>
      </simpara></listitem>
      <listitem><simpara>
      <command>"ncr-protocol": "UDP"</command>
      </simpara></listitem>
      <listitem><simpara>
      <command>"ncr-format": "JSON"</command>
      </simpara></listitem>
      <listitem><simpara>
      <command>"override-no-update": false</command>
      </simpara></listitem>
      <listitem><simpara>
      <command>"override-client-update": false</command>
      </simpara></listitem>
      <listitem><simpara>
      <command>"replace-client-name": "never"</command>
      </simpara></listitem>
      <listitem><simpara>
      <command>"generated-prefix": "myhost"</command>
      </simpara></listitem>
      </itemizedlist>
      </para>


      <section id="dhcpv6-d2-io-config">
      <title>DHCP-DDNS Server Connectivity</title>
      <para>
      In order for NCRs to reach the D2 server, kea-dhcp6 must be able
      to communicate with it.  kea-dhcp6 uses the following configuration
      parameters to control this communication:
      <itemizedlist>
      <listitem><simpara>
      <command>enable-updates</command> - determines whether or not kea-dhcp6 will
      generate NCRs.  If missing, this value is assumed to be false hence DDNS updates
      are disabled.  To enable DDNS updates set this value to true:
      </simpara></listitem>
      <listitem><simpara>
      <command>server-ip</command> - IP address on which D2 listens for requests. The default is
      the local loopback interface at address 127.0.0.1. You may specify
      either an IPv4 or IPv6 address.
      </simpara></listitem>
      <listitem><simpara>
      <command>server-port</command> - port on which D2 listens for requests.  The default value
      is 53001.
      </simpara></listitem>
      <listitem><simpara>
      <command>sender-ip</command> - IP address which kea-dhcp6 should use to send requests to D2.
      The default value is blank which instructs kea-dhcp6 to select a suitable
      address.
      </simpara></listitem>
      <listitem><simpara>
      <command>sender-port</command> - port which kea-dhcp6 should use to send requests to D2. The
      default value of 0 instructs kea-dhcp6 to select a suitable port.
      </simpara></listitem>
      <listitem><simpara>
      <command>max-queue-size</command> - maximum number of requests allowed to queue waiting to
      be sent to D2. This value guards against requests accumulating
      uncontrollably if they are being generated faster than they can be
      delivered.  If the number of requests queued for transmission reaches
      this value, DDNS updating will be turned off until the queue backlog has
      been sufficiently reduced.  The intent is to allow kea-dhcp6 to
      continue lease operations.  The default value is 1024.
      </simpara></listitem>
      <listitem><simpara>
      <command>ncr-protocol</command> - socket protocol use when sending requests to D2.  Currently
      only UDP is supported.  TCP may be available in an upcoming release.
      </simpara></listitem>
      <listitem><simpara>
      <command>ncr-format</command> - packet format to use when sending requests to D2.
      Currently only JSON format is supported.  Other formats may be available
      in future releases.
      </simpara></listitem>
      </itemizedlist>
      By default, kea-dhcp-ddns is assumed to running on the same machine as kea-dhcp6, and
      all of the default values mentioned above should be sufficient.
      If, however, D2 has been configured to listen on a different address or
      port, these values must altered accordingly. For example, if D2 has been
      configured to listen on 2001:db8::5 port 900, the following configuration
      would be required:
<screen>
"Dhcp6": {
    "dhcp-ddns": {
        <userinput>"server-ip": "2001:db8::5",
        "server-port": 900</userinput>,
        ...
    },
    ...
}
</screen>
      </para>
      </section>
      <section id="dhcpv6-d2-rules-config">
      <title>When Does kea-dhcp6 Generate a DDNS Request?</title>
      <para>kea-dhcp6 follows the behavior prescribed for DHCP servers in
      <ulink url="http://tools.ietf.org/html/rfc4704">RFC 4704</ulink>.
      It is important to keep in mind that kea-dhcp6 provides the initial
      decision making of when and what to update and forwards that
      information to D2 in the form of NCRs. Carrying out the actual
      DNS updates and dealing with such things as conflict resolution
      are within the purview of D2 itself (<xref linkend="dhcp-ddns-server"/>).
      This section describes when kea-dhcp6 will generate NCRs and the
      configuration parameters that can be used to influence this decision.
      It assumes that the <command>enable-updates</command> parameter is true.
      </para>
      <note>
        <para>
        Currently the interface between kea-dhcp6 and D2 only supports requests
        which update DNS entries for a single IP address.  If a lease grants
        more than one address, kea-dhcp6 will create the DDNS update request for
        only the first of these addresses.  Support for multiple address
        mappings may be provided in a future release.
        </para>
      </note>
      <para>
      In general, kea-dhcp6 will generate DDNS update requests when:
      <orderedlist>
      <listitem><para>
      A new lease is granted in response to a REQUEST
      </para></listitem>
      <listitem><para>
      An existing lease is renewed but the FQDN associated with it has
      changed.
      </para></listitem>
      <listitem><para>
      An existing lease is released in response to a RELEASE
      </para></listitem>
      </orderedlist>
      In the second case, lease renewal, two  DDNS requests will be issued: one
      request to remove entries for the previous FQDN and a second request to
      add entries for the new FQDN.  In the last case, a lease release, a
      single DDNS request to remove its entries will be made.
      </para>
      <para>
      The decision making involved when granting a new lease the first case) is more
      involved. When a new lease is granted, kea-dhcp6 will generate a DDNS
      update request only if the REQUEST contains the FQDN option (code 39).
      By default kea-dhcp6 will respect the FQDN N and S flags specified by the client
      as shown in the following table:
      </para>
        <table id="dhcp6-fqdn-flag-table">
          <title>Default FQDN Flag Behavior</title>
          <tgroup cols='4' align='left'>
          <colspec colname='cflags'/>
          <colspec colname='meaning'/>
          <colspec colname='response'/>
          <colspec colname='sflags'/>
          <thead>
              <row>
                <entry>Client Flags:N-S</entry>
                <entry>Client Intent</entry>
                <entry>Server Response</entry>
                <entry>Server Flags:N-S-O</entry>
              </row>
          </thead>
          <tbody>
            <row>
                <entry>0-0</entry>
                <entry>
                Client wants to do forward updates, server should do reverse updates
                </entry>
                <entry>Server generates reverse-only request</entry>
                <entry>1-0-0</entry>
            </row>
            <row>
                <entry>0-1</entry>
                <entry>Server should do both forward and reverse updates</entry>
                <entry>Server generates request to update both directions</entry>
                <entry>0-1-0</entry>
            </row>
            <row>
                <entry>1-0</entry>
                <entry>Client wants no updates done</entry>
                <entry>Server does not generate a request</entry>
                <entry>1-0-0</entry>
            </row>
          </tbody>
          </tgroup>
        </table>
      <para>
      The first row in the table above represents "client delegation". Here
      the DHCP client states that it intends to do the forward DNS updates and
      the server should do the reverse updates.  By default, kea-dhcp6 will honor
      the client's wishes and generate a DDNS request to D2 to update only
      reverse DNS data.  The parameter, <command>override-client-update</command>, can be used
      to instruct the server to override client delegation requests.  When
      this parameter is true, kea-dhcp6 will disregard requests for client
      delegation and generate a DDNS request to update both forward and
      reverse DNS data.  In this case, the N-S-O flags in the server's
      response to the client will be 0-1-1 respectively.
      </para>
      <para>
      (Note that the flag combination N=1, S=1 is prohibited according to
      <ulink url="http://tools.ietf.org/html/rfc4702">RFC 4702</ulink>. If such a
      combination is received from the client, the packet will be dropped by kea-dhcp6.)
      </para>
      <para>
      To override client delegation, set the following values in the configuration:
      </para>
<screen>
"Dhcp6": {
    "dhcp-ddns": {
        <userinput>"override-client-update": true</userinput>,
        ...
    },
    ...
}
</screen>
      <para>
      The third row in the table above describes the case in which the client
      requests that no DNS updates be done. The parameter, <command>override-no-update</command>,
      can be used to instruct the server to disregard the client's wishes. When
      this parameter is true, kea-dhcp6 will generate DDNS update requests to
      kea-dhcp-ddns even if the client requests no updates be done.  The N-S-O
      flags in the server's response to the client will be 0-1-1.
      </para>
      <para>
      To override client delegation, issue the following commands:
      </para>
<screen>
"Dhcp6": {
    "dhcp-ddns": {
        <userinput>"override-no-update": true</userinput>,
        ...
    },
    ...
}
</screen>
      </section>
      <section id="dhcpv6-fqdn-name-generation">
      <title>kea-dhcp6 Name Generation for DDNS Update Requests</title>
      <para>Each NameChangeRequest must of course include the fully qualified
      domain name whose DNS entries are to be affected.  kea-dhcp6 can be
      configured to supply a portion or all of that name based upon what it
      receives from the client.</para>
      <para>
       The default rules for constructing the FQDN that will be used for DNS
       entries are:
      <orderedlist>
      <listitem><para>
        If the DHCPREQUEST contains the client FQDN option, the candidate name
        is taken from there.
      </para></listitem>
      <listitem><para>
        If the candidate name is a partial (i.e. unqualified) name then add a
        configurable suffix to the name and use the result as the FQDN.
      </para></listitem>
      <listitem><para>
        If the candidate name provided is empty, generate an FQDN using a
        configurable prefix and suffix.
      </para></listitem>
      <listitem><para>
        If the client provided neither option, then no DNS action will be taken.
      </para></listitem>
      </orderedlist>
        These rules can amended by setting the
        <command>replace-client-name</command> parameter which provides the
        following modes of behavior:
      <itemizedlist>
      <listitem><para>
        <command>never</command> - Use the name the client sent.  If the client
        sent no name, do not generate one.  This is the default mode.
      </para></listitem>
      <listitem><para>
        <command>always</command> - Replace the name the client sent. If the
        client sent no name, generate one for the client.
      </para></listitem>
      <listitem><para>
        <command>when-present</command> - Replace the name the client sent.
        If the client sent no name, do not generate one.
      </para></listitem>
      <listitem><para>
        <command>when-not-present</command> - Use the name the client sent.
        If the client sent no name, generate one for the client.
      </para></listitem>
      </itemizedlist>
    <note>
    Note that formerly, this parameter was a boolean and permitted only values
    of <command>true</command> and <command>false</command>.  Boolean values
    have been deprecated and are no longer accepted.  If you are currently using
    booleans, you must replace them with the desired mode name. A value of
    <command>true</command> maps to <command>"when-present"</command>, while
    <command>false</command> maps to <command>"never"</command>.
    </note>

      For example, To instruct kea-dhcp6 to always generate the FQDN for a
      client, set the parameter <command>replace-client-name</command> to
      <command>always</command> as follows:
      </para>
<screen>
"Dhcp6": {
    "dhcp-ddns": {
        <userinput>"replace-client-name": "always"</userinput>,
        ...
    },
    ...
}
</screen>
      <para>
      The prefix used in the generation of an FQDN is specified by the
      <command>generated-prefix</command> parameter.  The default value is "myhost".  To alter
      its value, simply set it to the desired string:
      </para>
<screen>
"Dhcp6": {
    "dhcp-ddns": {
        <userinput>"generated-prefix": "another.host"</userinput>,
        ...
    },
    ...
}
</screen>
      <para>
      The suffix used when generating an FQDN or when qualifying a
      partial name is specified by
      the <command>qualifying-suffix</command> parameter. This
      parameter has no default value, thus it is mandatory when
      DDNS updates are enabled.
      To set its value simply set it to the desired string:
      </para>
<screen>
"Dhcp6": {
    "dhcp-ddns": {
        <userinput>"qualifying-suffix": "foo.example.org"</userinput>,
        ...
    },
    ...
}
</screen>
      </section>
      <para>
      When qualifying a partial name, kea-dhcp6 will construct a name with the
      format:
      </para>
      <para>
        [candidate-name].[qualifying-suffix].
      </para>
      <para>
      where candidate-name is the partial name supplied in the REQUEST.
      For example, if FQDN domain name value was "some-computer" and
      qualifying-suffix "example.com", the generated FQDN would be:
      </para>
      <para>
        some-computer.example.com.
      </para>
      <para>
      When generating the entire name, kea-dhcp6 will construct name of the
      format:
      </para>
      <para>
        [generated-prefix]-[address-text].[qualifying-suffix].
      </para>
      <para>
      where address-text is simply the lease IP address converted to a
      hyphenated string.  For example, if lease address is 3001:1::70E,
      the qualifying suffix "example.com", and the default value is used for
      <command>generated-prefix</command>, the generated FQDN would be:
      </para>
      <para>
        myhost-3001-1--70E.example.com.
      </para>
    </section>

    <section id="dhcp6-dhcp4o6-config">
      <title>DHCPv4-over-DHCPv6: DHCPv6 Side</title>
      <para>
      The support of DHCPv4-over-DHCPv6 transport is described in
      <ulink url="http://tools.ietf.org/html/rfc7341">RFC 7341</ulink>
      and is implemented using cooperating DHCPv4 and DHCPv6 servers.
      This section is about the configuration of the DHCPv6 side
      (the DHCPv4 side is described in <xref linkend="dhcp4-dhcp4o6-config"/>).
      </para>
      <note>
      DHCPv4-over-DHCPv6 support is experimental and the details of
      the inter-process communication can change: both the
      DHCPv4 and DHCPv6 sides should be running the same version of Kea.
      </note>
      <para>
      There is only one specific parameter for the DHCPv6 side:
      <command>dhcp4o6-port</command> which specifies the first of the
      two consecutive ports of the UDP sockets used for the communication
      between the DHCPv6 and DHCPv4 servers (the DHCPv6 server is bound
      to ::1 on <command>port</command> and connected to ::1 on
      <command>port</command> + 1).
      </para>
      <para>
      Two other configuration entries are in general required: unicast traffic
      support (see <xref linkend="dhcp6-unicast"/>) and DHCP 4o6 server
      address option (name "dhcp4o6-server-addr", code  88).
      </para>
      <para>
      The following configuration was used during some tests:
<screen>
{

# DHCPv6 conf
"Dhcp6": {

    "interfaces-config": {
        "interfaces": [ "eno33554984/2001:db8:1:1::1" ]
    },

    "lease-database": {
        "type": "memfile",
        "name": "leases6"
    },

    "preferred-lifetime": 3000,
    "valid-lifetime": 4000,
    "renew-timer": 1000,
    "rebind-timer": 2000,

    "subnet6": [ {
        "subnet": "2001:db8:1:1::/64",
        "interface": "eno33554984",
        "pools": [ { "pool": "2001:db8:1:1::1:0/112" } ]
    } ],

    <userinput>"dhcp4o6-port": 6767,

    "option-data": [ {
        "name": "dhcp4o6-server-addr",
        "code": 88,
        "space": "dhcp6",
        "csv-format": true,
        "data": "2001:db8:1:1::1"
    } ]
</userinput>
},

"Logging": {
    "loggers": [ {
        "name": "kea-dhcp6",
        "output_options": [ {
            "output": "/tmp/kea-dhcp6.log"
        } ],
        "severity": "DEBUG",
        "debuglevel": 0
    } ]
}

}
</screen>
      </para>
      <note>
      Relayed DHCPv4-QUERY DHCPv6 messages are not yet supported.
      </note>
    </section>

   </section>

  <!-- Host reservation is a large topic. There will be many subsections,
   so it should be a section on its own. -->
  <section id="host-reservation-v6">
    <title>Host Reservation in DHCPv6</title>

    <para>There are many cases where it is useful to provide a configuration on
    a per host basis. The most obvious one is to reserve specific, static IPv6
    address or/and prefix for exclusive use by a given client (host) &dash; returning
    client will get the same address or/and prefix every time and other clients will
    never get that address. Note that there may be cases when the
    new reservation has been made for the client for the address or prefix being
    currently in use by another client. We call this situation a "conflict". The
    conflicts get resolved automatically over time as described in the subsequent
    sections. Once conflict is resolved, the client will keep receiving the reserved
    configuration when it renews.</para>

    <para>Another example when the host reservations are applicable is when a host
    has specific requirements, e.g. a printer that needs additional DHCP options
    or a cable modem needs specific parameters. Yet another possible use case for
    host reservation is to define unique names for hosts.</para>

    <para>Hosts reservations are defined as parameters for each subnet. Each host
    can be identified by either DUID or its hardware/MAC address. See
    <xref linkend="mac-in-dhcpv6"/> for details. There is an optional
    <command>reservations</command> array in the
    <command>subnet6</command> structure. Each element in that array
    is a structure, that holds information about a single host. In
    particular, the structure has an identifier that
    uniquely identifies a host.  In the DHCPv6 context, such an identifier
    is usually a DUID, but can also be a hardware or MAC address.  Also,
    either one or more addresses or prefixes may be specified. It is
    possible to specify a hostname and DHCPv6 options for a given host.</para>

    <para>The following example shows how to reserve addresses and prefixes
    for specific hosts:

<screen>
"subnet6": [
    {
        "subnet": "2001:db8:1::/48",
        "pools": [ { "pool": "2001:db8:1::/80" } ],
        "pd-pools": [
            {
                "prefix": "2001:db8:1:8000::",
                "prefix-len": 48,
                "delegated-len": 64
            }
        ],
        <userinput>"reservations": [
            {
                "duid": "01:02:03:04:05:0A:0B:0C:0D:0E",
                "ip-addresses": [ "2001:db8:1::100" ]
            },
            {
                "hw-address": "00:01:02:03:04:05",
                "ip-addresses": [ "2001:db8:1::101", "2001:db8:1::102" ]
            },
            {
                "duid": "01:02:03:04:05:06:07:08:09:0A",
                "ip-addresses": [ "2001:db8:1::103" ],
                "prefixes": [ "2001:db8:2:abcd::/64" ],
                "hostname": "foo.example.com"
            }
        ]</userinput>
    }
]
</screen>

    This example includes reservations for three different clients. The first reservation
    is made for the address 2001:db8:1::100 for a client using DUID
    01:02:03:04:05:0A:0B:0C:0D:0E. The second reservation is made for two addresses
    2001:db8:1::101 and 2001:db8:1::102 for a client using MAC address
    00:01:02:03:04:05. Lastly, address 2001:db8:1::103 and prefix 2001:db8:2:abcd::/64
    are reserved for a client using DUID 01:02:03:04:05:06:07:08:09:0A. The
    last reservation also assigns a hostname to this client.
    </para>

    <para>Note that DHCPv6 allows for a single client to lease multiple addresses
    and multiple prefixes at the same time. Therefore <command>ip-addresses</command>
    and <command>prefixes</command> are plural and are actually arrays.
    When the client sends multiple IA options (IA_NA or IA_PD), each reserved
    address or prefix is assigned to an individual IA of the appropriate type. If
    the number of IAs of specific type is lower than the number of reservations
    of that type, the number of reserved addresses or prefixes assigned to the
    client is equal to the number of IA_NAs or IA_PDs sent by the client, i.e.
    some reserved addresses or prefixes are not assigned. However,
    they still remain reserved for this client and the server will not assign
    them to any other client. If the number of IAs of specific type sent by the
    client is greater than the number of reserved addresses or prefixes, the
    server will try to assign all reserved addresses or prefixes to the individual
    IAs and dynamically allocate addresses or prefixes to remaining IAs. If the
    server cannot assign a reserved address or prefix because it is in use,
    the server will select the next reserved address or prefix and try to assign it to
    the client. If the server subsequently finds that there are no more reservations
    that can be assigned to the client at the moment, the server will try to
    assign leases dynamically.
    </para>

    <para>Making a reservation for a mobile host that may visit multiple subnets
    requires a separate host definition in each subnet it is expected to visit.
    It is not allowed to define multiple host definitions with the same hardware
    address in a single subnet. Multiple host definitions with the same hardware
    address are valid if each is in a different subnet.  The reservation for a given host
    should include only one identifier, either DUID or hardware address. Defining
    both for the same host is considered a configuration error, but as of 1.1.0,
    it is not rejected.
    </para>

    <para>Adding host reservation incurs a performance penalty. In principle,
    when a server that does not support host reservation responds to a query,
    it needs to check whether there is a lease for a given address being
    considered for allocation or renewal. The server that also supports host
    reservation, has to perform additional checks: not only if the address is
    currently used (i.e. if there is a lease for it), but also whether the address
    could be used by someone else (i.e. if there is a reservation for it). That
    additional check incurs additional overhead.</para>

    <section id="reservation6-types">
      <title>Address/Prefix Reservation Types</title>

      <para>In a typical scenario there is an IPv6 subnet defined with a certain
      part of it dedicated for dynamic address allocation by the DHCPv6
      server. There may be an additional address space defined for prefix
      delegation. Those dynamic parts are referred to as dynamic pools, address
      and prefix pools or simply pools. In principle, the host reservation can
      reserve any address or prefix that belongs to the subnet. The reservations
      that specify an address that belongs to configured pools are called
      "in-pool reservations". In contrast, those that do not
      belong to dynamic pools are called "out-of-pool
      reservations". There is no formal difference in the reservation
      syntax and both reservation types are handled
      uniformly. However, upcoming releases may offer improved performance if
      there are only out-of-pool reservations as the server will be able to skip
      reservation checks when dealing with existing leases. Therefore, system
      administrators are encouraged to use out-of-pool reservations if
      possible.</para>
    </section>

    <section id="reservation6-conflict">
      <title>Conflicts in DHCPv6 Reservations</title>
      <para>As reservations and lease information are stored separately,
      conflicts may arise. Consider the following series of events. The server
      has configured the dynamic pool of addresses from the range of 2001:db8::10
      to 2001:db8::20. Host A requests an address and gets 2001:db8::10. Now the
      system administrator decides to reserve address 2001:db8::10 for Host B.
      In general, reserving an address
      that is currently assigned to someone else is not recommended, but there
      are valid use cases where such an operation is warranted.</para>

      <para>The server now has a conflict to resolve. Let's analyze the
      situation here. If Host B boots up and request an address, the server is
      not able to assign the reserved address 2001:db8::10. A naive approach
      would to be immediately remove the lease for Host A and create a new one
      for Host B. That would not solve the problem, though, because as soon as
      Host B get the address, it will detect that the address is already in use
      by someone else (Host A) and would send a Decline message. Therefore in this
      situation, the server has to temporarily assign a different address from the
      dynamic pool (not matching what has been reserved) to Host B.</para>

      <para>When Host A renews its address, the server will discover that
      the address being renewed is now reserved for someone else (Host
      B). Therefore the server will remove the lease for 2001:db8::10, select
      a new address and create a new lease for it. It will send two
      addresses in its response: the old address with lifetime set to 0 to
      explicitly indicate that it is no longer valid and the new address with a
      non-zero lifetime. When Host B renews its temporarily assigned
      address, the server will detect that the existing lease does not match
      reservation, so it will release the current address Host B has and will
      create a new lease matching the reservation. Similar as before, the server
      will send two addresses: the temporarily assigned one with zeroed
      lifetimes, and the new one that matches reservation with proper lifetimes
      set.</para>

      <para>This recovery will succeed, even if other hosts will attempt to get
      the reserved address. Had Host C requested address 2001:db8::10 after
      the reservation was made, the server will propose a different address.</para>

      <para>This recovery mechanism allows the server to fully recover from a
      case where reservations conflict with existing leases. This procedure
      takes time and will roughly take as long as renew-timer value specified.
      The best way to avoid such recovery is to not define new reservations that
      conflict with existing leases. Another recommendation is to use
      out-of-pool reservations. If the reserved address does not belong to a
      pool, there is no way that other clients could get this address.
      </para>
    </section>

    <section id="reservation6-hostname">
      <title>Reserving a Hostname</title>
      <para>When the reservation for the client includes the <command>hostname</command>,
      the server will assign this hostname to the client and send
      it back in the Client FQDN, if the client sent the FQDN option to the
      server. The reserved hostname always takes precedence over the hostname
       supplied by the client (via the FQDN option) or the autogenerated
      (from the IPv6 address) hostname.</para>

      <para>The server qualifies the reserved hostname with the value
      of the <command>qualifying-suffix</command> parameter. For example, the
      following subnet configuration:
<screen>
"subnet6": [
    {
        "subnet": "2001:db8:1::/48",
        "pools": [ { "pool": "2001:db8:1::/80" } ],
        "reservations": [
            {
                "duid": "01:02:03:04:05:0A:0B:0C:0D:0E",
                "ip-addresses": [ "2001:db8:1::100" ]
                "hostname": "alice-laptop"
            }
        ]
    }
],
"dhcp-ddns": {
    "enable-updates": true,
    "qualifying-suffix": "example.isc.org."
}
</screen>
      will result in assigning the "alice-laptop.example.isc.org." hostname to the
      client using the DUID "01:02:03:04:05:0A:0B:0C:0D:0E". If the <command>qualifying-suffix
      </command> is not specified, the default (empty) value will be used, and
      in this case the value specified as a <command>hostname</command> will
      be treated as fully qualified name.  Thus, by leaving the
      <command>qualifying-suffix</command> empty it is possible to qualify
      hostnames for the different clients with different domain names:
<screen>
"subnet6": [
    {
        "subnet": "2001:db8:1::/48",
        "pools": [ { "pool": "2001:db8:1::/80" } ],
        "reservations": [
            {
                "duid": "01:02:03:04:05:0A:0B:0C:0D:0E",
                "ip-addresses": [ "2001:db8:1::100" ]
                "hostname": "mark-desktop.example.org."
            }
        ]
    }
],
"dhcp-ddns": {
    "enable-updates": true,
}
</screen>
      The above example results in the assignment of the "mark-desktop.example.org." hostname to the
      client using the DUID "01:02:03:04:05:0A:0B:0C:0D:0E".
    </para>
</section>

    <section id="reservation6-options">
      <title>Including Specific DHCPv6 Options in Reservations</title>
      <para>Kea 1.1.0 introduced the ability to specify options on a
      per host basis. The options follow the same rules as any other
      options. These can be standard options (see <xref
      linkend="dhcp6-std-options" />), custom options (see <xref
      linkend="dhcp6-custom-options"/>) or vendor specific options
      (see <xref linkend="dhcp6-vendor-opts" />). The following
      example demonstrates how standard options can be defined.</para>

      <screen>
"reservations": [
{
   "duid": "01:02:03:05:06:07:08",
   "ip-addresses": [ "2001:db8:1::2" ],
    <userinput>"option-data": [
    {
        "option-data": [ {
            "name": "dns-servers",
            "data": "3000:1::234"
        },
        {
            "name": "nis-servers",
            "data": "3000:1::234"
        }
    } ]</userinput>
} ]</screen>

    <para>Vendor specific options can be reserved in a similar manner:</para>

    <screen>
"reservations": [
{
    "duid": "aa:bb:cc:dd:ee:ff",
    "ip-addresses": [ "2001:db8::1" ],
    <userinput>"option-data": [
    {
        "name": "vendor-opts",
        "data": 4491
    },
    {
        "name": "tftp-servers",
        "space": "vendor-4491",
        "data": "3000:1::234"
    } ]</userinput>
} ]</screen>

<para>
 Options defined on host level have the highest priority. In other words,
 if there are options defined with the same type on global, subnet, class and
 host level, the host specific values will be used.
</para>

    </section>

    <section id="reservation6-client-classes">
      <title>Reserving Client Classes in DHCPv6</title>
      <para>The <xref linkend="classification-using-expressions"/> explains how
      to configure the server to assign classes to a client based on the content
      of the options that this client sends to the server. Host reservations
      mechanisms also allow for the static assignment of classes to clients.
      The definitions of these classes are placed in the Kea
      configuration. The following configuration snippet shows how to specify
      that the client belongs to classes <command>reserved-class1</command>
      and <command>reserved-class2</command>. Those classes are associated with
      specific options being sent to the clients which belong to them.
      </para>
<screen>
{
    "client-classes": [
    {
       "name": "reserved-class1",
       "option-data": [
       {
           "name": "dns-servers",
           "data": "2001:db8:1::50"
       }
       ]
   },
   {
       "name": "reserved-class2",
       "option-data": [
       {
           "name": "nis-servers",
           "data": "2001:db8:1::100"
       }
       ]
    }
    ],
    "subnet6": [
    {   "pools": [ { "pool": "2001:db8:1::/64" } ],
        "subnet": "2001:db8:1::/48",
        "reservations": [
        {
            "duid": "01:02:03:04:05:06:07:08",
            <userinput>
            "client-classes": [ "reserved-class1", "reserved-class2" ]
            </userinput>
         } ]
     } ]
 }

</screen>
    <para>Static class assignments, as shown above, can be used in conjunction
    with classification using expressions.</para>
    </section>

    <section id="reservations6-mysql-pgsql">
      <title>Storing Host Reservations in MySQL or PostgreSQL</title>

      <para>
        It is possible to store host reservations in MySQL or PostgreSQL. See <xref
        linkend="hosts6-storage" /> for information on how to configure Kea to use
        reservations stored in MySQL or PostgreSQL. Kea does not provide any dedicated
        tools for managing reservations in a database. The Kea wiki <ulink
        url="http://kea.isc.org/wiki/HostReservationsHowTo" /> provides detailed
        information and examples of how reservations can be inserted into the
        database.
      </para>

      <note><simpara>In Kea 1.1.0 maximum length of an option specified per host is
      arbitrarily set to 4096 bytes.</simpara></note>
    </section>

    <section id="reservations6-cql">
      <title>Storing Host Reservations in CQL (Cassandra)</title>
      <para>Kea currently does not support storing reservations in
      Cassandra (CQL).</para>
    </section>

    <section id="reservations6-tuning">
      <title>Fine Tuning DHCPv6 Host Reservation</title>

      <para>The host reservation capability introduces additional restrictions for the
      allocation engine (the component of Kea that selects an address for a client)
      during lease selection and renewal. In particular, three
      major checks are necessary. First, when selecting a new lease, it is not
      sufficient for a candidate lease to not be used by another DHCP client. It
      also must not be reserved for another client. Second, when renewing a lease,
      additional check must be performed whether the address being renewed is not
      reserved for another client. Finally, when a host renews an address or a
      prefix, the server has to check whether there is a reservation for this host,
      so the existing (dynamically allocated) address should be revoked and the
      reserved one be used instead.</para>
      <para>Some of those checks may be unnecessary in certain deployments and not
      performing them may improve performance. The Kea server provides the
      <command>reservation-mode</command> configuration parameter to select the
      types of reservations allowed for the particular subnet. Each reservation
      type has different constraints for the checks to be performed by the
      server when allocating or renewing a lease for the client.
      Allowed values are:

      <itemizedlist>
      <listitem><simpara> <command>all</command> - enables all host reservation
      types. This is the default value. This setting is the safest and the most
      flexible. It allows in-pool and out-of-pool reservations. As all checks
      are conducted, it is also the slowest.
      </simpara></listitem>

      <listitem><simpara> <command>out-of-pool</command> - allows only out of
      pool host reservations.  With this setting in place, the server may assume
      that all host reservations are for addresses that do not belong to the
      dynamic pool. Therefore it can skip the reservation checks when dealing
      with in-pool addresses, thus improving performance. Do not use this mode
      if any of your reservations use in-pool address. Caution is advised when
      using this setting. Kea 1.1.0 does not sanity check the reservations against
      <command>reservation-mode</command> and misconfiguration may cause problems.
      </simpara></listitem>

      <listitem><simpara>
      <command>disabled</command> - host reservation support is disabled. As there
      are no reservations, the server will skip all checks. Any reservations defined
      will be completely ignored. As the checks are skipped, the server may
      operate faster in this mode.
      </simpara></listitem>

      </itemizedlist>
      </para>

      <para>
        An example configuration that disables reservation looks like follows:
        <screen>
"Dhcp6": {
    "subnet6": [
        {
        "subnet": "2001:db8:1::/64",
        <userinput>"reservation-mode": "disabled"</userinput>,
        ...
        }
    ]
}
</screen>
      </para>

      <para>Another aspect of the host reservations are different types of
      identifiers. Kea 1.1.0 supports two types of identifiers
      in DHCPv6: hw-address and duid, but more identifier types
      are likely to be added in the future. This is beneficial from a
      usability perspective. However, there is a drawback. For each incoming
      packet Kea has to to extract each identifier type and then query the
      database to see if there is a reservation done by this particular
      identifier. If nothing is found, the next identifier is extracted and next
      query is issued. This process continues until either a reservation is
      found or all identifier types have been checked. Over time with an increasing
      number of supported identifier types, Kea would become slower and
      slower.</para>

      <para>To address this problem, a parameter called
      <command>host-reservation-identifiers</command> has been introduced. It
      takes a list of identifier types as a parameter. Kea will check only those
      identifier types enumerated in host-reservation-identifiers. From a
      performance perspective the number of identifier types should be kept to
      minimum, ideally limited to one. If your deployment uses several
      reservation types, please enumerate them from most to least frequently
      used as this increases the chances of Kea finding the reservation using the
      fewest number of queries. An example of host reservation identifiers looks
      as follows:

<screen>
<userinput>"host-reservation-identifiers": [ "duid", "hw-address" ],</userinput>
"subnet6": [
    {
        "subnet": "2001:db8:1::/64",
        ...
    }
]</screen>
</para>

<para>
If not specified, the default value is:
<screen>
<userinput>"host-reservation-identifiers": [ "hw-address", "duid" ]</userinput>
</screen>

</para>
<!-- see CfgHostOperations::createConfig6() in
     src/lib/dhcpsrv/cfg_host_operations.cc -->

   </section>

    <!-- @todo: add support for per IA reservation (that specifies IAID in
                the ip-addresses and prefixes) -->
  </section>
  <!-- end of host reservations section -->

  <!-- shared networks starts here -->
  <section id="shared-network6">
    <title>Shared networks in DHCPv6</title>

    <para>DHCP servers use subnet information in two ways. First, it is used
    to determine the point of attachment, or simply put, where the client is
    connected to the network. Second, the subnet information is used to group
    information pertaining to specific location in the network. This approach
    works well in general case, but the are scenarios where the boundaries are
    blurred. Sometimes it is useful to have more than one logical IP subnet
    being deployed on the same physical link. The need to understand
    that two or more subnets are used on the same link requires additional logic
    in the DHCP server. This capability has been added in Kea 1.3.0.  It is
    called "shared networks" in Kea and ISC DHCP projects. It is sometimes also
    called "shared subnets". In Microsoft's nomenclature it is called "multinet".
    </para>

    <para>There are many use cases where the feature is useful. The most common
    example in the IPv4 case is when the server is running out of available
    addresses in a subnet. This is less common in IPv6, but the shared networks
    are still useful in IPv6. One of the use cases is an exhaustion of IPv6
    delegated prefixes within a subnet. Another IPv6 specific example
    is an experiment with addressing scheme. With the advent of IPv6 deployment
    and vast address space, many organizations split the address space into
    subnets, then deploy it and after a while discover that they want to split it
    differently. In the transition period they want both old and new addressing
    to be available. Thus the need for more than one subnet on the same physical
    link.</para>

    <para>Finally, the case of cable networks is directly applicable in
    IPv6. There are two types of devices in cable networks: cable modems and the
    end user devices behind them. It is a common practice to use different
    subnet for cable modems to prevent users from tinkering with their cable
    modems. In this case, the distinction is based on the type of device, rather
    than coming out of running out address space.</para>

    <para>In order to define a shared network an additional configuration scope
    is introduced:
<screen>
{
"Dhcp6": {
    <userinput>"shared-networks": [
        {
            // Name of the shared network. It may be an arbitrary string
            // and it must be unique among all shared networks.
            "name": "ipv6-lab-1",

            // Subnet selector can be specifed on the shared network level.
            // Subnets from this shared network will be selected for clients
            // communicating via relay agent having the specified IP address.
            "relay": {
                "ip-address": "2001:db8:2:34::1"
            },

            // This starts a list of subnets in this shared network.
            // There are two subnets in this example.
            "subnet6": [
                {
                    "subnet": "2001:db8::/48",
                    "pools": [ { "pool":  "2001:db8::1 - 2001:db8::ffff" } ]
                },
                {
                    "subnet": "3ffe:ffe::/64",
                    "pools": [ { "pool":  "3ffe:ffe::/64" } ]
                }
            ]
        } ]</userinput>, // end of shared-networks

    // It is likely that in your network you'll have a mix of regular,
    // "plain" subnets and shared networks. It is perfectly valid to mix
    // them in the same config file.
    //
    // This is regular subnet. It's not part of any shared-network.
    "subnet6": [
        {
            "subnet": "2001:db9::/48",
            "pools": [ { "pool":  "2001:db9::/64" } ],
            "relay": {
                "ip-address": "2001:db8:1:2::1"
            }
        }
    ]

} // end of Dhcp6
}
</screen>
    </para>
    <para>As you see in the example, it is possible to mix shared and regular
    ("plain") subnets. Each shared network must have a unique name. This is a
    similar concept to ID for subnets, but it offers more flexibility. This is used
    for logging, but also internally for identifying shared networks.</para>

    <para>In principle it makes sense to define only shared networks that
    consist of two or more subnets. However, for testing purposes it is allowed
    to define a shared network with just one subnet or even an empty one.  This
    is not a recommended practice in production networks, as the shared network
    logic requires additional processing and thus lowers server's performance.
    To avoid unnecessary performance degradation the shared subnets should only
    be defined when required by the deployment.
    </para>

    <para>Shared networks provide an ability to specify many parameters in
    the shared network scope that will apply to all subnets within it. If
    necessary, you can specify a parameter in the shared network scope and then
    override its value on the subnet scope. For example:
<screen>
"shared-networks": [
    {
        "name": "lab-network3",
        "relay": {
             "ip-address": "2001:db8:2:34::1"
        },

        // This applies to all subnets in this shared network, unless
        // values are overridden on subnet scope.
        <userinput>"valid-lifetime": 600</userinput>,

        // This option is made available to all subnets in this shared
        // network.
        <userinput>"option-data": [ {
            "name": "dns-servers",
            "data": "2001:db8::8888"
        } ]</userinput>,

        "subnet6": [
            {
                "subnet": "2001:db8:1::/48",
                "pools": [ { "pool":  "2001:db8:1::1 - 2001:db8:1::ffff" } ],

                // This particular subnet uses different values.
                <userinput>"valid-lifetime": 1200,
                "option-data": [
                {
                    "name": "dns-servers",
                    "data": "2001:db8::1:2"
                },
                {
                    "name": "unicast",
                    "data": "2001:abcd::1"
                } ]</userinput>
            },
            {
                 "subnet": "2001:db8:2::/48",
                 "pools": [ { "pool":  "2001:db8:2::1 - 2001:db8:2::ffff" } ],

                 // This subnet does not specify its own valid-lifetime value,
                 // so it is inherited from shared network scope.
                 <userinput>"option-data": [
                 {
                     "name": "dns-servers",
                     "data": "2001:db8:cafe::1"
                 } ]</userinput>
            }
        ],
    } ]</screen>

    In this example, there is a dns-servers option defined that is available to
    clients in both subnets in this shared network. Also, a valid lifetime is
    set to 10 minutes (600s). However, the first subnet overrides some of the values
    (valid lifetime is 20 minutes, different IP address for dns-servers), but
    also adds its own option (unicast address). Assuming a client asking for a
    server unicast and dns servers options is assigned a lease from this subnet,
    he will get a lease for 20 minutes and dns-servers and be allowed to use
    server unicast at address 2001:abcd::1. If the same client is assigned to
    the second subnet, he will get a 10 minutes long lease, dns-servers value of
    2001:db8:cafe::1 and no server unicast.
    </para>

    <section>
      <title>Local and relayed traffic in shared networks</title>

    <para>It is possible to specify interface name in the shared network scope to
    tell the server that this specific shared network is reachable directly (not
    via relays) using local network interface. It is sufficient to specify
    it once in the shared network level. As all subnets in a shared network are
    expected to be used on the same physical link, it is a configuration error
    to attempt to make a shared network out of subnets that are reachable over
    different interfaces. It is allowed to specify interface parameter on each
    subnet, although its value must be the same for each subnet. Thus it's
    usually more convenient to specify it once on the shared network level.
<screen>
"shared-networks": [
    {
        "name": "office-floor-2",

        // This tells Kea that the whole shared networks is reachable over
        // local interface. This applies to all subnets in this network.
        <userinput>"interface": "eth0"</userinput>,

        "subnet6": [
            {
                "subnet": "2001:db8::/64",
                "pools": [ { "pool":  "2001:db8::1 - 2001:db8::ffff" } ],
                <userinput>"interface": "eth0"</userinput>
            },
            {
                 "subnet": "3ffe:abcd::/64",
                 "pools": [ { "pool":  "3ffe:abcd::1 - 3ffe:abcd::ffff" } ]

                 // Specifying a different interface name is configuration
                 // error:
                 // "interface": "eth1"
            }
        ],
    } ]
</screen>
</para>

<para>Somewhat similar to interface names, also relay IP addresses can be
specified for the whole shared network. However, depending on your relay
configuration, it may use different IP addresses depending on which subnet
is being used. Thus there is no requirement to use the same IP relay address
for each subnet. Here's an example:

<screen>
"shared-networks": [
    {"
        "name": "kakapo",
        <userinput>"relay": {
            "ip-address": "2001:db8::abcd"
        }</userinput>,
        "subnet6": [
            {
                "subnet": "2001:db8::/64",
                <userinput>"relay": {
                    "ip-address": "2001:db8::1234"
                }</userinput>,
                "pools": [ { "pool":  "2001:db8::1 - 2001:db8::ffff" } ]
            },
            {
                 "subnet": "3ffe:abcd::/64",
                 "pools": [ { "pool":  "3ffe:abcd::1 - 3ffe:abcd::ffff" } ],
                 <userinput>"relay": {
                    "ip-address": "3ffe:abcd::cafe"
                 }</userinput>
            }
        ]
    }
]</screen>
In this particular case the relay IP address specified on network level doesn't
have much sense, as it is overridden in both subnets, but it was left there
as an example of how one could be defined on network level. Note that the
relay agent IP address typically belongs to the subnet it relays packets from,
but this is not a strict requirement. Therefore Kea accepts any value here
as long as it is valid IPv6 address.</para>

    </section>
    <section>
      <title>Client classification in shared networks</title>

<para>Sometimes it is desired to segregate clients into specific subnets.
A case of cable network where modems should use one subnet and other devices
should use another subnet is a good example. For that reason Kea allows for
restricting access to specific subnets based on client classification. See <xref
linkend="classify"/> for details on how to define client classes.

The following example defines two classes of devices. The decision is made
based on option 1234 values.
<screen>
{
    "client-classes": [
        {

            "name": "a-devices",
            "test": "option[1234].hex == 0x0001"
        },
        {
            "name": "b-devices",
            "test": "option[1234].hex == 0x0002"
        }
    ],
    "shared-networks": [
        {
            "name": "galah",
            "relay": {
                "ip-address": "2001:db8:2:34::1"
            },
            "subnet6": [
                {
                    "subnet": "2001:db8:1::/64",
                    "pools": [ { "pool": "2001:db8:1::20 - 2001:db8:1::ff" } ],
                    <userinput>"client-class": "a-devices"</userinput>
                },
                {
                    "subnet": "2001:db8:3::/64",
                    "pools": [ { "pool": "2001:db8:3::20 - 2001:db8:3::ff" } ],
                    <userinput>"client-class": "b-devices"</userinput>
                }
            ]
        }
    ]
}
</screen>
In this example each class has its own restriction. Only clients that belong to
class a-devices will be able to use subnet 2001:db8:1::/64 and only clients
belonging to b-devices will be able to use subnet 2001:db8:3::/64. Care should
be taken to not define too restrictive classification rules, as clients that are
not able to use any subnets will be refused service. Although, this may be
desired outcome if one desires to service only clients of known properties
(e.g. only VoIP phones allowed on a given link).</para>

    <para>
      Note that it is possible to achieve similar effect as presented in this
      section without the use of shared networks. If the subnets are placed in
      the global subnets scope, rather than in the shared network, the server
      will still use classification rules to pick the right subnet for a given
      class of devices. The major benefit of placing subnets within the
      shared network is that common parameters for the logically grouped
      subnets can be specified once, in the shared network scope, e.g.
      "interface" or "relay" parameter. All subnets belonging to this shared
      network will inherit those parameters.
    </para>

    </section>

    <section>
      <title>Host reservations in shared networks</title>

<para>
  Subnets being part of a shared network allow host reservations, similar to
  regular subnets:
  <screen>
{
    "shared-networks": [
    {
        "name": "frog",
        "relay": {
            "ip-address": "2001:db8:2:34::1"
        },
        "subnet6": [
            {
                "subnet": "2001:db8:1::/64",
                "id": 100,
                "pools": [ { "2001:db8:1::1 - 2001:db8:1::64" } ],
                <userinput>"reservations": [
                {
                    "duid": "00:03:00:01:11:22:33:44:55:66",
                    "ip-addresses": [ "2001:db8:1::28" ]
                }
                ]</userinput>
            },
            {
                "subnet": "2001:db8:3::/64",
                "id": 101,
                "pools": [ { "pool": "2001:db8:3::1 - 2001:db8:3::64" } ],
                <userinput>"reservations": [
                    {
                        "duid": "00:03:00:01:aa:bb:cc:dd:ee:ff",
                        "ip-addresses": [ "2001:db8:2::28" ]
                    }
                ]</userinput>
            }
        ]
    }
    ]
}
  </screen>
</para>
<para>It is worth noting that Kea conducts additional checks when processing a
packet if shared networks are defined. First, instead of simply checking if
there's a reservation for a given client in his initially selected subnet, it
goes through all subnets in a shared network looking for a reservation. This is
one of the reasons why defining a shared network may impact performance. If
there is a reservation for a client in any subnet, that particular subnet will
be picked for the client. Although it's technically not an error, it is
considered a bad practice to define reservations for the same host in multiple
subnets belonging to the same shared network.</para>

<para>While not strictly mandatory, it is strongly recommended to use explicit
"id" values for subnets if you plan to use database storage for host
reservations. If ID is not specified, the values for it be autogenerated,
i.e. it will assign increasing integer values starting from 1.</para>
    </section>

  </section>

  <!-- end of shared networks -->

    <section id="dhcp6-serverid">
      <title>Server Identifier in DHCPv6</title>
      <para>The DHCPv6 protocol uses a "server identifier" (also known
      as a DUID) for clients to be able to discriminate between several
      servers present on the same link.
      <ulink url="http://tools.ietf.org/html/rfc3315">RFC 3315</ulink>
      defines three DUID types: DUID-LLT, DUID-EN and DUID-LL.
      <ulink url="http://tools.ietf.org/html/rfc6355">RFC 6355</ulink>
      also defines DUID-UUID. Future specifications may introduce new
      DUID types.</para>

      <para>The Kea DHCPv6 server generates a server identifier once, upon
      the first startup, and stores it in a file. This identifier isn't
      modified across restarts of the server and so is a stable identifier.</para>

      <para>Kea follows recommendation from
      <ulink url="http://tools.ietf.org/html/rfc3315">RFC 3315</ulink>
      to use DUID-LLT as the default server identifier. However, we have
      received reports that some deployments require different DUID
      types, and there is a need to administratively select both DUID
      type and/or its contents.</para>

      <para>The server identifier can be configured using parameters
      within the <command>server-id</command> map element in the global
      scope of the Kea configuration file. The following example
      demonstrates how to select DUID-EN as a server identifier:

<screen>
"Dhcp6": {
    "server-id": {
        "type": "EN"
    },
    ...
}
</screen>

      </para>

      <para>Currently supported values for <command>type</command>
      parameter are: "LLT", "EN" and "LL", for DUID-LLT, DUID-EN and
      DUID-LL respectively.</para>

      <para>When a new DUID type is selected the server will generate its
      value and replace any existing DUID in the file. The server will then
      use the new server identifier in all future interactions with the
      clients.</para>

      <note><para>If the new server identifier is created after some clients
      have obtained their leases, the clients using the old identifier will not
      be able to renew the leases: the server will ignore messages
      containing the old server identifier. Clients will continue sending
      Renew until they transition to the rebinding state. In this state they
      will start sending Rebind messages to multicast address without
      a server identifier. The server will respond to the Rebind messages
      with a new server identifier and the clients will associate the
      new server identifier with their leases. Although the clients will
      be able to keep their leases and will eventually learn the new server
      identifier, this will be at the cost of increased number of renewals
      and multicast traffic due to a need to rebind. Therefore it is
      recommended that modification of the server identifier type
      and value is avoided if the server has already assigned leases and these
      leases are still valid.</para></note>

      <para>There are cases when an administrator needs to explicitly
      specify a DUID value rather than allow the server to generate it.
      The following example demonstrates how to explicitly set all
      components of a DUID-LLT.

<screen>
"Dhcp6": {
    "server-id": {
        "type": "LLT",
        "htype": 8,
        "identifier": "A65DC7410F05",
        "time": 2518920166
    },
    ...
}
</screen>

      where:
      <itemizedlist>
        <listitem><simpara><command>htype</command> is a 16-bit unsigned value
        specifying hardware type,</simpara></listitem>
        <listitem><simpara><command>identifier</command> is a link layer
        address, specified as a string of hexadecimal digits,</simpara>
        </listitem>
        <listitem><simpara><command>time</command> is a 32-bit unsigned
        time value.</simpara></listitem>
      </itemizedlist>
      </para>

      <para>The hexadecimal representation of the DUID generated as a result
      of the configuration specified above will be:
<screen>
 00:01:00:08:96:23:AB:E6:A6:5D:C7:41:0F:05
|type |htype|   time    |   identifier    |
</screen>
      </para>

      <para>It is allowed to use special value of 0 for "htype" and "time",
      which indicates that the server should use ANY value for these
      components. If the server already uses a DUID-LLT it will use the
      values from this DUID. If the server uses a DUID of a different type
      or doesn't use any DUID yet, it will generate these values.
      Similarly, if the "identifier" is assigned an empty string, the
      value of the identifier will be generated. Omitting any of these
      parameters is equivalent to setting them to those special values.
      </para>

      <para>For example, the following configuration:
<screen>
"Dhcp6": {
    "server-id": {
        "type": "LLT",
        "htype": 0,
        "identifier": "",
        "time": 2518920166
    },
    ...
}
</screen>

      indicates that the server should use ANY link layer address and
      hardware type. If the server is already using DUID-LLT it will
      use the link layer address and hardware type from the existing DUID.
      If the server is not using any DUID yet, it will use link layer
      address and hardware type from one of the available network
      interfaces. The server will use an explicit value of time. If it
      is different than a time value present in the currently used
      DUID, that value will be replaced, effectively causing
      modification of the current server identifier.
      </para>

      <para>
        The following example demonstrates an explicit configuration of
        a DUID-EN:

<screen>
"Dhcp6": {
    "server-id": {
        "type": "EN",
        "enterprise-id": 2495,
        "identifier": "87ABEF7A5BB545"
    },
    ...
}
</screen>

      where:
      <itemizedlist>
        <listitem><simpara><command>enterprise-id</command> is a 32-bit
        unsigned value holding enterprise number,</simpara></listitem>
        <listitem><simpara><command>identifier</command> is a variable
        length identifier within DUID-EN.</simpara></listitem>
      </itemizedlist>
      </para>

      <para>
        The hexadecimal representation of the DUID-EN created according to
        the configuration above is:
<screen>
 00:02:00:00:09:BF:87:AB:EF:7A:5B:B5:45
|type |  ent-id   |     identifier     |
</screen>
      </para>

      <para>As in the case of the DUID-LLT, special values can be used for the
      configuration of the DUID-EN. If <command>enterprise-id</command> is 0, the server
      will use a value from the existing DUID-EN. If the server is not using
      any DUID or the existing DUID has a different type, the ISC enterprise
      id will be used. When an empty string is used for <command>identifier</command>, the
      identifier from the existing DUID-EN will be used. If the server is
      not using any DUID-EN the new 6-bytes long identifier will be generated.
      </para>

      <para>DUID-LL is configured in the same way as DUID-LLT with an exception
      that the <command>time</command> parameter has no effect for DUID-LL,
      because this DUID type only comprises a hardware type and link layer
      address. The following example demonstrates how to configure DUID-LL:

<screen>
"Dhcp6": {
    "server-id": {
        "type": "LL",
        "htype": 8,
        "identifier": "A65DC7410F05"
    },
    ...
}
</screen>

      </para>

      <para>
      which will result in the following server identifier:

<screen>
 00:03:00:08:A6:5D:C7:41:0F:05
|type |htype|   identifier    |
</screen>
      </para>

      <para>The server stores the generated server identifier in the following
      location: [kea-install-dir]/var/kea/kea-dhcp6-serverid.
      </para>

      <para>In some uncommon deployments where no stable storage is
      available, the server should be configured not to try to
      store the server identifier. This choice is controlled
      by the value of <command>persist</command> boolean parameter:
<screen>
"Dhcp6": {
    "server-id": {
        "type": "EN",
        "enterprise-id": 2495,
        "identifier": "87ABEF7A5BB545",
        "persist": false
    },
    ...
}
</screen>
      </para>
      <para>The default value of the "persist" parameter is
      <command>true</command> which configures the server to store the
      server identifier on a disk.</para>

      <para>In the example above, the server is configured to not store
      the generated server identifier on a disk. But, if the server
      identifier is not modified in the configuration the same value
      will be used after server restart, because entire server
      identifier is explicitly specified in the configuration.</para>
    </section>

    <section id="stateless-dhcp6">
      <title>Stateless DHCPv6 (Information-Request Message)</title>
      <para>Typically DHCPv6 is used to assign both addresses and options. These
      assignments (leases) have state that changes over time, hence
      their name, stateful. DHCPv6 also supports a stateless mode,
      where clients request configuration options only. This mode is
      considered lightweight from the server perspective as it does not require
      any state tracking; hence its name.</para>
      <para>The Kea server supports stateless mode. Clients can send
      Information-Request messages and the server will send back
      answers with the requested options (providing the options are
      available in the server configuration).  The server will attempt to
      use per-subnet options first. If that fails - for whatever reason - it
      will then try to provide options defined in the global scope.</para>

      <para>Stateless and stateful mode can be used together. No special
      configuration directives are required to handle this. Simply use the
      configuration for stateful clients and the stateless clients will get
      just options they requested.</para>

      <para>This usage of global options allows for an interesting case.
      It is possible to run a server that provides just options and no
      addresses or prefixes. If the options have the same value in each
      subnet, the configuration can define required options in the global
      scope and skip subnet definitions altogether. Here's a simple example of
      such a configuration:
<screen>
"Dhcp6": {
    "interfaces-config": {
        "interfaces": [ "ethX" ]
    },
    <userinput>"option-data": [ {
        "name": "dns-servers",
        "data": "2001:db8::1, 2001:db8::2"
    } ]</userinput>,
    "lease-database": { "type": "memfile" }
 }
</screen>
      This very simple configuration will provide DNS server information
      to all clients in the network, regardless of their location. Note the
      specification of the memfile lease database: this is needed as
      Kea requires a lease database to be specified
      even if it is not used.</para>
    </section>

    <section id="dhcp6-rfc7550">
      <title>Support for RFC 7550</title>
      <para>The <ulink url="http://tools.ietf.org/html/rfc7550">RFC 7550</ulink>
      introduced some changes to the DHCPv6 protocol to resolve a few issues
      with the coexistence of multiple stateful options in the messages sent
      between the clients and servers.</para>

      <para>The typical example is when the client, such as a requesting
      router, requests an allocation of both addresses and prefixes when
      it performs the 4-way (SARR) exchange with the server. If the
      server is not configured to allocate any prefixes but it can allocate
      some addresses, it will respond with the IA_NA(s) containing allocated
      addresses and the IA_PD(s) containing the NoPrefixAvail status code. If
      the client can operate without prefixes it may transition to the
      'bound' state when it sends Renew/Rebind messages to the server,
      according to the T1 and T2 times, to extend the lifetimes of the
      allocated addresses. If the client is still interested in obtaining
      prefixes from the server it may also include an IA_PD in the Renew/Rebind
      to request allocation of the prefixes. If the server still cannot
      allocate the prefixes, it will respond with the IA_PD(s) containing
      NoPrefixAvail status code. However, if the server can now allocate
      the prefixes it will do so, and send them in the IA_PD(s) to the client.
      Allocation of leases during the Renew/Rebind was not supported in the
      <ulink url="http://tools.ietf.org/html/rfc3315">RFC 3315</ulink>
      and <ulink url="http://tools.ietf.org/html/rfc3633">RFC 3633</ulink>,
      and has been introduced in
      <ulink url="http://tools.ietf.org/html/rfc7550">RFC 7550</ulink>.
      Kea supports this new behavior and it doesn't provide any configuration
      mechanisms to disable it.
      </para>

      <para>
        The following are the other behaviors specified in the
        <ulink url="http://tools.ietf.org/html/rfc7550">RFC 7550</ulink>
        supported by the Kea DHCPv6 server:
        <itemizedlist>
          <listitem><simpara>Set T1/T2 timers to the same value for all
          stateful (IA_NA and IA_PD) options to facilitate renewal of all
          client's leases at the same time (in a single message exchange),
          </simpara></listitem>
          <listitem><simpara>NoAddrsAvail and NoPrefixAvail status codes
          are placed in the IA_NA and IA_PD options in the Advertise message,
          rather than as the top level options.</simpara></listitem>
        </itemizedlist>
      </para>
    </section>

    <section id="dhcp6-relay-override">
      <title>Using Specific Relay Agent for a Subnet</title>
      <para>
        The relay has to have an interface connected to the link on which
        the clients are being configured. Typically the relay has a global IPv6
        address configured on the interface that belongs to the subnet from which
        the server will assign addresses. In the typical case, the
        server is able to use the IPv6 address inserted by the relay (in the link-addr
        field in RELAY-FORW message) to select the appropriate subnet.
      </para>
      <para>
        However, that is not always the case. The relay
        address may not match the subnet in certain deployments. This
        usually means that there is more than one subnet allocated for a given
        link. The two most common examples where this is the case are long lasting
        network renumbering (where both old and new address space is still being
        used) and a cable network. In a cable network both cable modems and the
        devices behind them are physically connected to the same link, yet
        they use distinct addressing. In such case, the DHCPv6 server needs
        additional information (like the value of interface-id option or IPv6
        address inserted in the link-addr field in RELAY-FORW message) to
        properly select an appropriate subnet.
      </para>
      <para>
        The following example assumes that there is a subnet 2001:db8:1::/64
        that is accessible via a relay that uses 3000::1 as its IPv6 address.
        The server will be able to select this subnet for any incoming packets
        that came from a relay with an address in 2001:db8:1::/64 subnet.
        It will also select that subnet for a relay with address 3000::1.
        <screen>
"Dhcp6": {
    "subnet6": [
        {
            "subnet": "2001:db8:1::/64",
            "pools": [
                 {
                     "pool": "2001:db8:1::1-2001:db8:1::ffff"
                 }
             ],
             <userinput>"relay": {
                 "ip-address": "3000::1"
             }</userinput>
        }
    ]
}
</screen>
      </para>

      <para>If "relay" is specified, the "ip-address" parameter within
      it is mandatory.</para>

    </section>

      <section id="dhcp6-client-class-relay">
        <title>Segregating IPv6 Clients in a Cable Network</title>
        <para>
          In certain cases, it is useful to mix relay address information,
          introduced in <xref linkend="dhcp6-relay-override"/> with client
          classification, explained in <xref linkend="classify"/>.
          One specific example is a cable network, where typically modems
          get addresses from a different subnet than all devices connected
          behind them.
        </para>
        <para>
          Let's assume that there is one CMTS (Cable Modem Termination System)
          with one CM MAC (a physical link that modems are connected to).
          We want the modems to get addresses from the 3000::/64 subnet,
          while everything connected behind modems should get addresses from
          another subnet (2001:db8:1::/64). The CMTS that acts as a relay
          an uses address 3000::1. The following configuration can serve
          that configuration:
        <screen>
"Dhcp6": {
    "subnet6": [
        {
            "subnet": "3000::/64",
            "pools": [
                { "pool": "3000::2 - 3000::ffff" }
            ],
            <userinput>"client-class": "VENDOR_CLASS_docsis3.0",
            "relay": {
                "ip-address": "3000::1"
            }</userinput>
        },

        {
            "subnet": "2001:db8:1::/64",
            "pools": [
                 {
                     "pool": "2001:db8:1::1-2001:db8:1::ffff"
                 }
             ],
             <userinput>"relay": {
                 "ip-address": "3000::1"
             }</userinput>
        }
    ]
}
</screen>
      </para>
      </section>

    <section id="mac-in-dhcpv6">
      <title>MAC/Hardware Addresses in DHCPv6</title>
      <para>MAC/hardware addresses are available in DHCPv4 messages
      from the clients and administrators
      frequently use that information to perform certain tasks, like per host
      configuration, address reservation for specific MAC addresses and other.
      Unfortunately, the DHCPv6 protocol does not provide any completely reliable way
      to retrieve that information. To mitigate that issue a number of mechanisms
      have been implemented in Kea that attempt to gather it. Each
      of those mechanisms works in certain cases, but may fail in other cases.
      Whether the mechanism works or not in the particular deployment is
      somewhat dependent on the network topology and the technologies used.</para>

      <para>Kea allows configuration of which of the supported methods should be
      used and in what order. This configuration may be considered a fine tuning
      of the DHCP deployment. In a typical deployment the default
      value of <command>"any"</command> is sufficient and there is no
      need to select specific methods. Changing the value of this parameter
      is the most useful in cases when an administrator wants to disable
      certain method, e.g. if the administrator trusts the network infrastructure
      more than the information provided by the clients themselves, the
      administrator may prefer information provided by the relays over that
      provided by the clients.
      </para>
      <para>
      The configuration is controlled by the <command>mac-sources</command>
      parameter as follows:
        <screen>
"Dhcp6": {
    <userinput>"mac-sources": [ "method1", "method2", "method3", ... ]</userinput>,

    "subnet6": [ ... ],

    ...
}
</screen>

    When not specified, a special value of "any" is used, which
    instructs the server to attempt to use all the methods in sequence and use
    value returned by the first one that succeeds. If specified, it
    has to have at least one value.</para>

    <para>Supported methods are:
    <itemizedlist>
      <listitem>
        <simpara><command>any</command> - Not an actual method, just a keyword that
        instructs Kea to try all other methods and use the first one that succeeds.
        This is the default operation if no <command>mac-sources</command> are defined.
        </simpara>
      </listitem>
      <listitem>
        <simpara><command>raw</command> - In principle, a DHCPv6 server could use raw
        sockets to receive incoming traffic and extract MAC/hardware address
        information. This is currently not implemented for DHCPv6 and this value has
        no effect.
        </simpara>
      </listitem>
      <listitem>
        <simpara><command>duid</command> - DHCPv6 uses DUID identifiers instead of
        MAC addresses. There are currently four DUID types defined, with two of them
        (DUID-LLT, which is the default one and DUID-LL) convey MAC address information.
        Although <ulink utl="http://tools.ietf.org/html/rfc3315">RFC 3315</ulink> forbids
        it, it is possible to parse those DUIDs and extract
        necessary information from them. This method is not completely reliable, as
        clients may use other DUID types, namely DUID-EN or DUID-UUID.
        </simpara>
      </listitem>
      <listitem>
        <simpara><command>ipv6-link-local</command> - Another possible acquisition
        method comes from the source IPv6 address. In typical usage, clients are
        sending their packets from IPv6 link-local addresses. There is a good chance
        that those addresses are based on EUI-64, which contains MAC address. This
        method is not completely reliable, as clients may use other link-local address
        types.  In particular, privacy extensions, defined in
        <ulink url="http://tools.ietf.org/html/rfc4941">RFC 4941</ulink>, do not use
        MAC addresses.  Also note that successful extraction requires that the
        address's u-bit must be set to 1 and its g-bit set to 0, indicating that it
        is an interface identifier as per
        <ulink url="http://tools.ietf.org/html/rfc2373#section-2.5.1">
        RFC 2373, section 2.5.1</ulink>.
        </simpara>
      </listitem>
      <listitem>
        <simpara><command>client-link-addr-option</command> - One extension defined
        to alleviate missing MAC issues is client link-layer address option, defined
        in <ulink url="http://tools.ietf.org/html/rfc6939">RFC 6939</ulink>. This is
        an option that is inserted by a relay and contains information about client's
        MAC address. This method requires a relay agent that supports the option and
        is configured to insert it. This method is useless for directly connected
        clients. This parameter can also be specified as <command>rfc6939</command>,
        which is an alias for <command>client-link-addr-option</command>.
        </simpara>
      </listitem>
      <listitem>
        <simpara><command>remote-id</command> -
        <ulink url="http://tools.ietf.org/html/rfc4649">RFC 4649</ulink>
        defines a remote-id option that is inserted by a relay agent. Depending
        on the relay agent configuration, the inserted option may convey the client's
        MAC address information. This parameter can also be specified as
        <command>rfc4649</command>, which is an alias for <command>remote-id</command>.
        </simpara>
      </listitem>
      <listitem>
        <simpara><command>subscriber-id</command> - Another option
        that is somewhat similar to the previous one is subscriber-id,
        defined in <ulink url="http://tools.ietf.org/html/rfc4580">RFC
        4580</ulink>. It is, too, inserted by a relay agent that is
        configured to insert it. This parameter can also be specified
        as <command>rfc4580</command>, which is an alias for
        <command>subscriber-id</command>. This method is currently not
        implemented.
        </simpara>
      </listitem>
      <listitem>
        <simpara><command>docsis-cmts</command> - Yet another possible source of MAC
        address information are the DOCSIS options inserted by a CMTS that acts
        as a DHCPv6 relay agent in cable networks. This method attempts to extract
        MAC address information from suboption 1026 (cm mac) of the vendor specific option
        with vendor-id=4491. This vendor option is extracted from the relay-forward message,
        not the original client's message.
        </simpara>
      </listitem>
      <listitem>
        <simpara><command>docsis-modem</command> - Yet another possible source of MAC
        address information are the DOCSIS options inserted by the cable modem itself.
        This method attempts to extract MAC address information from suboption 36 (device id)
        of the vendor specific option with vendor-id=4491. This vendor option is extracted from
        the original client's message, not from any relay options.
        </simpara>
      </listitem>
    </itemizedlist>
  </para>

  <para>Empty mac-sources is not allowed. If you do not want to specify it,
  either simply omit mac-sources definition or specify it with the "any" value
  which is the default.</para>
  </section>

    <section id="dhcp6-decline">
      <title>Duplicate Addresses (DECLINE Support)</title>

      <para>The DHCPv6 server is configured with a certain pool of
      addresses that it is expected to hand out to the DHCPv6 clients.
      It is assumed that the server is authoritative and has complete
      jurisdiction over those addresses. However, due to various
      reasons, such as misconfiguration or a faulty client implementation
      that retains its address beyond the valid lifetime, there may be
      devices connected that use those addresses without the server's
      approval or knowledge.</para>

      <para>Such an unwelcome event can be detected
      by legitimate clients (using Duplicate Address Detection) and
      reported to the DHCPv6 server using a DECLINE message. The server
      will do a sanity check (if the client declining an address really
      was supposed to use it), then will conduct a clean up operation
      and confirm it by sending back a REPLY message. Any DNS entries
      related to that address will be removed, the fact will be logged
      and hooks will be triggered. After that is done, the address
      will be marked as declined (which indicates that it is used by
      an unknown entity and thus not available for assignment to
      anyone) and a probation time will be set on it. Unless otherwise
      configured, the probation period lasts 24 hours. After that
      period, the server will recover the lease (i.e. put it back into
      the available state) and the address will be available for assignment
      again. It should be noted that if the underlying issue of a
      misconfigured device is not resolved, the duplicate address
      scenario will repeat. On the other hand, it provides an
      opportunity to recover from such an event automatically, without
      any sysadmin intervention.</para>

      <para>To configure the decline probation period to a value other
      than the default, the following syntax can be used:
<screen>
  "Dhcp6": {
    <userinput>"decline-probation-period": 3600</userinput>,
    "subnet6": [ ... ],
    ...
}
</screen>
      The parameter is expressed in seconds, so the example above will instruct
      the server to recycle declined leases after an hour.</para>

      <para>There are several statistics and hook points associated with the
      Decline handling procedure. The lease6_decline hook is triggered after the
      incoming Decline message has been sanitized and the server is about to decline
      the lease. The declined-addresses statistic is increased after the
      hook returns (both global and subnet specific variants). (See
      <xref linkend="dhcp4-stats"/> and <xref linkend="hooks-libraries"/> for more details
      on DHCPv4 statistics and Kea hook points.)</para>

      <para>Once the probation time elapses, the declined lease is recovered
      using the standard expired lease reclamation procedure, with several
      additional steps. In particular, both declined-addresses statistics
      (global and subnet specific) are decreased. At the same time,
      reclaimed-declined-addresses statistics (again in two variants, global and
      subnet specific) are increased.</para>

      <para>Note about statistics: The server does not decrease the
      assigned-addresses statistics when a DECLINE message is received and
      processed successfully. While technically a declined address is no longer
      assigned, the primary usage of the assigned-addresses statistic is to
      monitor pool utilization. Most people would forget to include
      declined-addresses in the calculation, and simply do
      assigned-addresses/total-addresses. This would have a bias towards
      under-representing pool utilization. As this has a potential for major
      issues, we decided not to decrease assigned addresses immediately after
      receiving Decline, but to do it later when we recover the address back to
      the available pool.</para>
    </section>

    <section id="dhcp6-stats">
      <title>Statistics in the DHCPv6 Server</title>
      <note>
        <para>This section describes DHCPv6-specific statistics. For a general
        overview and usage of statistics, see <xref linkend="stats" />.</para>
      </note>

      <para>
        The DHCPv6 server supports the following statistics:
      </para>
        <table frame="all" id="dhcp6-statistics">
          <title>DHCPv6 Statistics</title>
          <tgroup cols='3'>
          <colspec colname='statistic' align='center'/>
          <colspec colname='type' align='center'/>
          <colspec colname='description' align='left'/>
          <thead>
            <row>
              <entry>Statistic</entry>
              <entry>Data Type</entry>
              <entry>Description</entry>
            </row>
          </thead>
          <tbody>

            <row>
              <entry>pkt6-received</entry>
              <entry>integer</entry>
              <entry>Number of DHCPv6 packets received. This includes all packets:
              valid, bogus, corrupted, rejected etc. This statistic is expected
              to grow rapidly.</entry>
            </row>

            <row>
              <entry>pkt6-receive-drop</entry>
              <entry>integer</entry>
              <entry>Number of incoming packets that were dropped. The exact reason
              for dropping packets is logged, but the most common reasons may
              be: an unacceptable or not supported packet type, direct responses
              are forbidden, the server-id sent by the client does not match the
              server's server-id or the packet is malformed.</entry>
            </row>

            <row>
              <entry>pkt6-parse-failed</entry>
              <entry>integer</entry>
              <entry>Number of incoming packets that could not be parsed.
              A non-zero value of this statistic indicates that the server
              received a malformed or truncated packet. This may indicate problems
              in your network, faulty clients, faulty relay agents or a bug in the
              server.</entry>
            </row>

            <row>
              <entry>pkt6-solicit-received</entry>
              <entry>integer</entry>
              <entry>
                Number of SOLICIT packets received. This statistic is expected
                to grow.  Its increase means that clients that just booted
                started their configuration process and their initial packets
                reached your server.
              </entry>
            </row>

            <row>
              <entry>pkt6-advertise-received</entry>
              <entry>integer</entry>
              <entry>
                Number of ADVERTISE packets received. Advertise packets are sent
                by the server and the server is never expected to receive them. A non-zero
                value of this statistic indicates an error occurring in the network.
                One likely cause would be a misbehaving relay agent that incorrectly
                forwards ADVERTISE messages towards the server rather back to the
                clients.
              </entry>
            </row>

            <row>
              <entry>pkt6-request-received</entry>
              <entry>integer</entry>
              <entry>Number of REQUEST packets received. This statistic
                is expected to grow. Its increase means that clients that just booted
                received the server's response (ADVERTISE), accepted it and are now
                requesting an address (REQUEST).
              </entry>
            </row>

            <row>
              <entry>pkt6-reply-received</entry>
              <entry>integer</entry>
              <entry>Number of REPLY packets received. This statistic is
              expected to remain zero at all times, as REPLY packets are sent by
              the server and the server is never expected to receive
              them. A non-zero value indicates an error. One likely cause would be
              a misbehaving relay agent that incorrectly forwards REPLY messages
              towards the server, rather back to the clients.
              </entry>
            </row>

            <row>
              <entry>pkt6-renew-received</entry>
              <entry>integer</entry>
              <entry>Number of RENEW packets received. This statistic
                is expected to grow. Its increase means that clients received their
                addresses and prefixes and are trying to renew them.
              </entry>
            </row>

            <row>
              <entry>pkt6-rebind-received</entry>
              <entry>integer</entry>
              <entry>Number of REBIND packets received. A non-zero value
              indicates that clients didn't receive responses to their RENEW messages
              (regular lease renewal mechanism) and are attempting to find any server
              that is able to take over their leases. It may mean that some server's
              REPLY messages never reached the clients.
              </entry>
            </row>

            <row>
              <entry>pkt6-release-received</entry>
              <entry>integer</entry>
              <entry>Number of RELEASE packets received. This statistic is expected
              to grow when a device is being shut down in the network. It
              indicates that the address or prefix assigned is reported as no longer
              needed. Note that many devices, especially wireless, do not send RELEASE
              packets either because of design choice or due to the client moving out
              of range.
              </entry>
            </row>

            <row>
            <entry>pkt6-decline-received</entry>
            <entry>integer</entry>
            <entry>
              Number of DECLINE packets received. This statistic is expected to
              remain close to zero. Its increase means that a client leased an
              address, but discovered that the address is currently used by an
              unknown device in your network. If this statistic is growing, it
              may indicate a misconfigured server or devices that have statically
              assigned conflicting addresses.
            </entry>
            </row>

            <row>
              <entry>pkt6-infrequest-received</entry>
              <entry>integer</entry>
              <entry>
                Number of INFORMATION-REQUEST packets received. This statistic
                is expected to grow if there are devices that are using
                stateless DHCPv6. INFORMATION-REQUEST messages are used by
                clients that request stateless configuration, i.e. options
                and parameters other than addresses or prefixes.
              </entry>
            </row>

            <row>
              <entry>pkt6-dhcpv4-query-received</entry>
              <entry>integer</entry>
              <entry>
                Number of DHCPv4-QUERY packets received. This
                statistic is expected to grow if there are devices
                that are using DHCPv4-over-DHCPv6. DHCPv4-QUERY
                messages are used by DHCPv4 clients on an IPv6 only
                line which encapsulates the requests over DHCPv6.
              </entry>
            </row>

            <row>
              <entry>pkt6-dhcpv4-response-received</entry>
              <entry>integer</entry>
              <entry>
                Number of DHCPv4-RESPONSE packets received. This
                statistic is expected to remain zero at all times, as
                DHCPv4-RESPONSE packets are sent by the server and the
                server is never expected to receive them. A non-zero
                value indicates an error.  One likely cause would be a
                misbehaving relay agent that incorrectly forwards
                DHCPv4-RESPONSE message towards the server rather
                back to the clients.
              </entry>
            </row>

            <row>
              <entry>pkt6-unknown-received</entry>
              <entry>integer</entry>
              <entry>Number of packets received of an unknown type. A non-zero
              value of this statistic indicates that the server received a
              packet that it wasn't able to recognize: either it had an unsupported
              type or was possibly malformed.</entry>
            </row>

            <row>
              <entry>pkt6-sent</entry>
              <entry>integer</entry>
              <entry>Number of DHCPv6 packets sent. This statistic is expected
              to grow every time the server transmits a packet. In general, it
              should roughly match pkt6-received, as most incoming packets cause
              the server to respond. There are exceptions (e.g. server receiving a
              REQUEST with server-id matching other server), so do not worry, if
              it is lesser than pkt6-received.</entry>
            </row>

            <row>
              <entry>pkt6-advertise-sent</entry>
              <entry>integer</entry>
              <entry>Number of ADVERTISE packets sent. This statistic is
              expected to grow in most cases after a SOLICIT is processed. There
              are certain uncommon, but valid cases where incoming SOLICIT is
              dropped, but in general this statistic is expected to be close to
              pkt6-solicit-received.</entry>
            </row>

            <row>
              <entry>pkt6-reply-sent</entry>
              <entry>integer</entry>
              <entry>Number of REPLY packets sent. This statistic is expected to
              grow in most cases after a SOLICIT (with rapid-commit), REQUEST,
              RENEW, REBIND, RELEASE, DECLINE or INFORMATION-REQUEST is
              processed. There are certain cases where there is no response.
              </entry>
            </row>

            <row>
              <entry>pkt6-dhcpv4-response-sent</entry>
              <entry>integer</entry>
              <entry>Number of DHCPv4-RESPONSE packets sent. This
              statistic is expected to grow in most cases after a
              DHCPv4-QUERY is processed. There are certain cases where
              there is no response.
              </entry>
            </row>

            <row>
            <entry>subnet[id].total-nas</entry>
            <entry>integer</entry>
            <entry>
            This statistic shows the total number of NA addresses available for
            DHCPv6 management for a given subnet. In other words, this is the sum
            of all addresses in all configured pools. This statistic changes only
            during configuration changes. Note that it does not take into account any
            addresses that may be reserved due to host reservation. The
            <emphasis>id</emphasis> is the subnet-id of a given subnet. This
            statistic is exposed for each subnet separately and is
            reset during a reconfiguration event.
            </entry>
            </row>

            <row>
            <entry>subnet[id].assigned-nas</entry>
            <entry>integer</entry>
            <entry>
            This statistic shows the number of NA addresses in a given subnet that
            are assigned. This statistic increases every time a new lease is allocated
            (as a result of receiving a REQUEST message) and is decreased every time a
            lease is released (a RELEASE message is received) or expires. The
            <emphasis>id</emphasis> is the subnet-id of a given subnet. This
            statistic is exposed for each subnet separately and is
            reset during a reconfiguration event.
            </entry>
            </row>

            <row>
            <entry>subnet[id].total-pds</entry>
            <entry>integer</entry>
            <entry>
            This statistic shows the total number of PD prefixes available for
            DHCPv6 management for a given subnet. In other words, this is the sum
            of all prefixes in all configured pools. This statistic changes only
            during configuration changes. Note it does not take into account any
            prefixes that may be reserved due to host reservation. The
            <emphasis>id</emphasis> is the subnet-id of a given subnet. This
            statistic is exposed for each subnet separately and is
            reset during a reconfiguration event.
            </entry>
            </row>

            <row>
            <entry>subnet[id].assigned-pds</entry>
            <entry>integer</entry>
            <entry>
            This statistic shows the number of PD prefixes in a given subnet that
            are assigned. This statistic increases every time a new lease is allocated
            (as a result of receiving a REQUEST message) and is decreased every time a
            lease is released (a RELEASE message is received) or expires. The
            <emphasis>id</emphasis> is the subnet-id of a given subnet. This statistic
            is exposed for each subnet separately and is reset during a
            reconfiguration event.
            </entry>
            </row>

            <row>
              <entry>reclaimed-leases</entry>
              <entry>integer</entry>
              <entry> This statistic is the number of expired leases that have been
              reclaimed since server startup. It is incremented each time an expired
              lease is reclaimed (it counts both NA and PD reclamations) and is reset
              when the server is reconfigured.
              </entry>
            </row>

            <row>
              <entry>subnet[id].reclaimed-leases</entry>
              <entry>integer</entry>
              <entry>This statistic is the number of expired leases associated with
              a given subnet (<emphasis>"id"</emphasis> is the subnet-id) that have
              been reclaimed since server startup. It is incremented each time an expired
              lease is reclaimed (it counts both NA and PD reclamations) and is reset
              when the server is reconfigured.
              </entry>
            </row>

            <row>
            <entry>declined-addresses</entry>
            <entry>integer</entry>
            <entry>
              This statistic shows the number of IPv6 addresses that are
              currently declined and so counts the number of leases
              currently unavailable. Once a lease is recovered, this
              statistic will be decreased. Ideally, this statistic should be
              zero. If this statistic is non-zero (or worse, increasing),
              the network administrator should investigate if there is
              a misbehaving device in the network. This is a global statistic
              that covers all subnets.
            </entry>
            </row>

            <row>
            <entry>subnet[id].declined-addresses</entry>
            <entry>integer</entry>
            <entry>
              This statistic shows the number of IPv6 addresses that are
              currently declined in a given subnet. This statistic counts the
              number of leases currently unavailable. Once a lease is
              recovered, this statistic will be decreased. Ideally, this
              statistic should be zero. If this statistic is
              non-zero (or worse, increasing), a network administrator should
              investigate if there is a misbehaving device in the network. The
              <emphasis>id</emphasis> is the subnet-id of a given subnet. This
              statistic is exposed for each subnet separately.
            </entry>
            </row>

            <row>
            <entry>reclaimed-declined-addresses</entry>
            <entry>integer</entry>
            <entry>
              This statistic shows the number of IPv6 addresses that were
              declined, but have now been recovered. Unlike
              declined-addresses, this statistic never decreases. It can be used
              as a long term indicator of how many actual valid Declines were
              processed and recovered from. This is a global statistic that
              covers all subnets.
            </entry>
            </row>

            <row>
            <entry>subnet[id].reclaimed-declined-addresses</entry>
            <entry>integer</entry>
            <entry>
              This statistic shows the number of IPv6 addresses that were
              declined, but have now been recovered. Unlike
              declined-addresses, this statistic never decreases. It can be used
              as a long term indicator of how many actual valid Declines were
              processed and recovered from. The
              <emphasis>id</emphasis> is the subnet-id of a given subnet. This
              statistic is exposed for each subnet separately.
            </entry>
            </row>

        </tbody>
        </tgroup>
        </table>
    </section>

    <section id="dhcp6-ctrl-channel">
      <title>Management API for the DHCPv6 Server</title>
      <para>
        The management API allows the issuing of specific
        management commands, such as statistics retrieval, reconfiguration or shutdown.
        For more details, see <xref linkend="ctrl-channel" />. Currently the only
        supported communication channel type is UNIX stream socket. By default there
        are no sockets open. To instruct Kea to open a socket, the following entry
        in the configuration file can be used:
<screen>
"Dhcp6": {
    "control-socket": {
        "socket-type": "unix",
        "socket-name": <userinput>"/path/to/the/unix/socket"</userinput>
    },

    "subnet6": [
        ...
    ],
    ...
}
</screen>
      </para>

      <para>
        The length of the path specified by the <command>socket-name</command>
        parameter is restricted by the maximum length for the unix socket name
        on your operating system, i.e. the size of the <command>sun_path</command>
        field in the <command>sockaddr_un</command> structure, decreased by 1.
        This value varies on different operating systems between 91 and 107
        characters. Typical values are 107 on Linux and 103 on FreeBSD.
      </para>

      <para>
        Communication over control channel is conducted using JSON structures.
        See the Control Channel section in the Kea Developer's Guide for more details.
      </para>

      <para>The DHCPv6 server supports the following operational commands:
        <itemizedlist>
            <listitem>build-report</listitem>
            <listitem>config-get</listitem>
            <listitem>config-reload</listitem>
            <listitem>config-set</listitem>
            <listitem>config-test</listitem>
            <listitem>config-write</listitem>
            <listitem>leases-reclaim</listitem>
            <listitem>list-commands</listitem>
            <listitem>shutdown</listitem>
            <listitem>version-get</listitem>
        </itemizedlist>
         as described in <xref linkend="commands-common"/>.  In addition,
         it supports the following statistics related commands:
        <itemizedlist>
            <listitem>statistic-get</listitem>
            <listitem>statistic-reset</listitem>
            <listitem>statistic-remove</listitem>
            <listitem>statistic-get-all</listitem>
            <listitem>statistic-reset-all</listitem>
            <listitem>statistic-remove-all</listitem>
        </itemizedlist>
        as described here <xref linkend="command-stats"/>.
      </para>

    </section>

      <section>
        <title>User contexts in IPv6</title>
        <para>
          Kea allows loading hook libraries that sometimes could benefit from
          additional parameters. If such a parameter is specific to the whole
          library, it is typically defined as a parameter for the hook library.
          However, sometimes there is a need to specify parameters that are
          different for each pool.
        </para>

        <para>
          User contexts can store arbitrary data as long as it is valid JSON
          syntax and its top level element is a map (i.e. the data must be
          enclosed in curly brackets). Some hook libraries may expect specific
          formatting, though.  Please consult specific hook library
          documentation for details.
        </para>

        <para>
          User contexts can be specified on either subnet or pool level. One
          other useful usage is the ability to store comments or descriptions.
        </para>

        <para>
          Let's consider an example where certain parameters are supposed
          to be delivered to clients in form of additional options,
          and the values of those options are correlated to delegated
          prefixes. It seems reasonable to keep those parameters with
          the the definition of the PD pool. On the other hand, this
          functionality is is not part of the base Kea code so Kea will
          not understand any hook-specific keywords in that definition.
          The solution to this problem is to use user context. For
          each PD pool that is expected to be used with this feature,
          a "user context" is defined.  This is a structure that holds the
          parameters used by the hook library when it is loaded.
          An example configuration could look as follows:
          <screen>
"Dhcp6": {
    "subnet6": [ {
        "pd-pools": [
        {
            "prefix":  "2001:db8::",
            "prefix-len": 56,
            "delegated-len": 64,

            // This is a pool specific context.
            <userinput>"user-context": {
                "threshold-percent": 85,
                "v4-network": "192.168.0.0/16",
                "v4-overflow": "10.0.0.0/16"
            }</userinput>
        } ],
        "subnet": "2001:db8::/32",

        // This is a subnet specific context. You can put any type of
        // information here as long as it is a valid JSON.
        <userinput>"user-context": {
            "comment": "Those v4-v6 migration technologies are tricky.",
            "experimental": true,
            "billing-department": 42,
            "contact-points": [ "Alice", "Bob" ]
        }</userinput>
    } ],
    ...
}</screen>
        </para>

        <para>
          Kea does not interpret or use the content of the user context:
          it just stores it, making it available to the hook
          libraries. It is up to each hook library to extract the information
          and make use of it.
        </para>
        <para>
          For more background information, see <xref linkend="user-context"/>.
        </para>
    </section>

    <section id="dhcp6-std">
      <title>Supported DHCPv6 Standards</title>
      <para>The following standards are currently
      supported:</para>
      <itemizedlist>
          <listitem>
            <simpara><emphasis>Dynamic Host Configuration Protocol for IPv6</emphasis>,
            <ulink url="http://tools.ietf.org/html/rfc3315">RFC 3315</ulink>:
            Supported messages are SOLICIT,
            ADVERTISE, REQUEST, RELEASE, RENEW, REBIND, INFORMATION-REQUEST,
            CONFIRM and REPLY.</simpara>
          </listitem>
          <listitem>
            <simpara><emphasis>IPv6 Prefix Options for
            Dynamic Host Configuration Protocol (DHCP) version 6</emphasis>,
            <ulink url="http://tools.ietf.org/html/rfc3633">RFC 3633</ulink>:
            Supported options are IA_PD and
            IA_PREFIX. Also supported is the status code NoPrefixAvail.</simpara>
          </listitem>
          <listitem>
            <simpara><emphasis>DNS Configuration options for Dynamic Host
            Configuration Protocol for IPv6 (DHCPv6)</emphasis>,
            <ulink url="http://tools.ietf.org/html/rfc3646">RFC 3646</ulink>:
            Supported option is DNS_SERVERS.</simpara>
          </listitem>
          <listitem>
            <simpara><emphasis>The Dynamic Host Configuration Protocol for IPv6 (DHCPv6)
            Relay Agent Remote-ID Option</emphasis>,
            <ulink url="http://tools.ietf.org/html/rfc4649">RFC 4649</ulink>:
            REMOTE-ID option is supported.</simpara>
          </listitem>
          <listitem>
            <simpara><emphasis>The Dynamic Host Configuration Protocol for IPv6 (DHCPv6) Client
            Fully Qualified Domain Name (FQDN) Option</emphasis>,
            <ulink url="http://tools.ietf.org/html/rfc4704">RFC 4704</ulink>:
            Supported option is CLIENT_FQDN.</simpara>
          </listitem>
          <listitem>
            <simpara><emphasis>Dynamic Host Configuration Protocol for IPv6 (DHCPv6)
            Option for Dual-Stack Lite</emphasis>,
            <ulink url="http://tools.ietf.org/html/rfc6334">RFC 6334</ulink>:
            the AFTR-Name DHCPv6 Option is supported.</simpara>
          </listitem>
          <listitem>
            <simpara><emphasis>Relay-Supplied DHCP Options</emphasis>,
            <ulink url="http://tools.ietf.org/html/rfc6422">RFC 6422</ulink>:
            Full functionality is supported: OPTION_RSOO, ability of the server
            to echo back the options, checks whether an option is RSOO-enabled,
            ability to mark additional options as RSOO-enabled.</simpara>
          </listitem>
          <listitem>
            <simpara><emphasis>Prefix Exclude Option for DHCPv6-based Prefix
            Delegation</emphasis>,
            <ulink url="http://tools.ietf.org/html/rfc6603">RFC
            6603</ulink>: Prefix Exclude option is supported.</simpara>
          </listitem>
          <listitem>
            <simpara><emphasis>Client Link-Layer Address Option in
            DHCPv6</emphasis>,
            <ulink url="http://tools.ietf.org/html/rfc6939">RFC
            6939</ulink>: Supported option is client link-layer
            address option.</simpara>
          </listitem>
          <listitem>
            <simpara><emphasis>Issues and Recommendations with Multiple
            Stateful DHCPv6 Options</emphasis>,
            <ulink url="http://tools.ietf.org/html/rfc7550">RFC
            7550</ulink>: All recommendations related to the DHCPv6 server
            operation are supported.</simpara>
          </listitem>
      </itemizedlist>
    </section>

    <section id="dhcp6-limit">
      <title>DHCPv6 Server Limitations</title>
      <para> These are the current limitations of the DHCPv6 server
      software. Most of them are reflections of the early stage of
      development and should be treated as <quote>not implemented
      yet</quote>, rather than actual limitations.</para>
      <itemizedlist>
        <listitem>
          <simpara>
            The server will allocate, renew or rebind a maximum of one lease
            for a particular IA option (IA_NA or IA_PD) sent by a client.
            <ulink url="http://tools.ietf.org/html/rfc3315">RFC 3315</ulink> and
            <ulink url="http://tools.ietf.org/html/rfc3633">RFC 3633</ulink> allow
            for multiple addresses or prefixes to be allocated for a single IA.
          </simpara>
        </listitem>

        <listitem>
          <simpara>Temporary addresses are not supported.</simpara>
        </listitem>

        <listitem>
          <simpara>
            Client reconfiguration (RECONFIGURE) is not yet supported.
          </simpara>
        </listitem>
      </itemizedlist>
    </section>

    <section id="dhcp6-srv-examples">
      <title>Kea DHCPv6 server examples</title>

      <para>
        A collection of simple to use examples for DHCPv6 component of Kea is
        available with the sources. It is located in doc/examples/kea6
        directory. At the time of writing this text there were 18 examples,
        but the number is growing slowly with each release.
      </para>

    </section>

  </chapter>