kea/doc/examples/kea6/advanced.json

# This is an example configuration file for DHCPv6 server in Kea.
# It attempts to showcase some of the more advanced features.
# Topology wise, it's a basic scenario with one IPv6 subnet configured.
# It is assumed that one subnet (2001:db8:1::/64) is available directly
# over ethX interface.
#
# The following features are currently showcased here:
# 1. Configuration of MAC/hardware address sources in DHCPv6

{ "Dhcp6":

{
# Kea is told to listen on ethX network interface only.
  "interfaces-config": {
    "interfaces": [ "ethX" ]
  },

# We need to specify lease type. As of May 2014, three backends are supported:
# memfile, mysql and pgsql. We'll just use memfile, because it doesn't require
# any prior set up.
  "lease-database": {
    "type": "memfile"
  },

# Kea 0.9.1 introduced MAC/hardware addresses support in DHCPv6. There is
# no single reliable method of getting MAC address information in DHCPv6.
# Kea supports several methods. Depending on your network set up, some
# methods may be more preferable than others, hence the configuration
# parameter. 'mac-sources' is a list of methods. Allowed parameters are:
# any, raw, duid, ipv6-link-local, client-link-addr-option, rfc6939 (which
# is an alias for client-link-addr-option), remote-id, rfc4649 (which is an
# alias for remote-id, subscriber-id, rfc4580 (which is an alias for
# subscriber-id) and docsis.
#
# Note that the order matters. Methods are attempted one by one in the order
# specified until hardware address is obtained. If you don't care which method
# is used, using 'any' is marginally faster than enumerating them all.
#
# If mac-sources are not specified, a default value of 'any' is used.
  "mac-sources": [ "client-link-addr-option", "duid", "ipv6-link-local" ],

# RFC6422 defines a mechanism called relay-supplied options option. The relay
# agent may insert certain options that the server will echo back to the
# client, if certain criteria are met. One condition is that the option must
# be RSOO-enabled (i.e. allowed to be echoed back). IANA maintains a list
# of those options here:
# http://www.iana.org/assignments/dhcpv6-parameters/dhcpv6-parameters.xhtml#options-relay-supplied
# However, it is possible to allow the server to echo back additional options.
# This entry marks options 110, 120 and 130 as RSOO-enabled.
   "relay-supplied-options": [ "110", "120", "130" ],"

# Addresses will be assigned with preferred and valid lifetimes
# being 3000 and 4000, respectively. Client is told to start
# renewing after 1000 seconds. If the server does not respond
# after 2000 seconds since the lease was granted, client is supposed
# to start REBIND procedure (emergency renewal that allows switching
# to a different server).
  "preferred-lifetime": 3000,
  "valid-lifetime": 4000,
  "renew-timer": 1000,
  "rebind-timer": 2000,

# The following list defines subnets. Each subnet consists of at
# least subnet and pool entries.
  "subnet6": [
    {
      "pools": [ { "pool": "2001:db8:1::/80" } ],
      "subnet": "2001:db8:1::/64",
      "interface": "ethX"
    }
  ]
},

# The following configures logging. Kea will log all debug messages
# to /var/log/kea-debug.log file.
"Logging": {
    "loggers": [
        {
            "name": "kea-dhcp6",
            "output_options": [
                {
                    "output": "/var/log/kea-debug.log"
                }
            ],
            "debuglevel": 99,
            "severity": "DEBUG"
        }
    ]
}

}